What kind of problem can a broken center bolt in a rear leaf spring cause? - ANSWER Rear axle offset, which may produce a steering pull to the opposite direction of the offset.
What can cause excessive front caster on
...
What kind of problem can a broken center bolt in a rear leaf spring cause? - ANSWER Rear axle offset, which may produce a steering pull to the opposite direction of the offset.
What can cause excessive front caster on a front wheel? - ANSWER A broken center bolt in a rear leaf spring, on the vehicle wheel directly behind the front wheel.
How does caster affect steering pull? - ANSWER Steering pulls to the side with the least positive caster.
Can tire pressure affect steering pull? - ANSWER Yes.
What problem does excessive toe in cause? Does it affect steering pull? - ANSWER Cause feathered tire wear, but does not affect steering pull.
What is steering axis inclination (SAI)? - ANSWER Toe out on turns.
Does toe out affect steering while driving straight ahead? - ANSWER No.
Does positive camber affect steering pull? - ANSWER Yes.
Does ride height affect a proper alignment? - ANSWER Yes.
What will happen if there is improper ride height on a front wheel drive vehicle? - ANSWER If there is too much angle at the constant velocity joints of the drive axles, there will be vibrations, especially during acceleration.
What is the only steering linkage component that can have free play? - ANSWER The idler arm.
What should you do if you find any loose steering linkage component except for idler arm? - ANSWER Should be replaced.
What should you do first if you're aligning a vehicle with rear steering? - ANSWER Should make sure that the rear alignment is correct before any corrections are made in the front.
Should the rear steering system be in its centered position while front adjustments are being checked and adjusted? - ANSWER Yes.
What two things can happen by not setting the idler arm adjustment properly? - ANSWER Can cause vibrations and shorten tire life.
What kind of steering problem would a defective steering box, or rack and pinion cause? - ANSWER Steering problems, but mostly loss of assist in both directions.
What causes steering assist problems in one direction? - ANSWER The control valve or it's seals.
What is and the most likely cause of torque steer? - ANSWER Torque steer is when the vehicles moves to one side of the lane during acceleration. This is caused by unequal forces transmitted from the drive train through unequal length drive axles on front-wheel-drive vehicles.
What is and the most likely cause of bump steer? - ANSWER Bump steer is caused by rack shifting in its bushings, this is when the vehicle hits a hole or bump on the road.
What is and the most likely cause memory steer? - ANSWER Memory steering is when the vehicle continues to steer or pull in the same direction as the last sharp turn. This is caused by tie rod ends losing their resiliency, the rubberized material slips a little and the new position is the new working center.
What is usually adjustable on vehicles with torsion bars? - ANSWER Ride height.
What should be checked before any alignment measurements or adjustments are made? - ANSWER Ride height.
What wheel alignment value does ride height affect? - ANSWER Camber, caster, and toe.
Can ride height be adjusted on vehicles with torsion bars? - ANSWER Yes.
Can ride height be adjusted on vehicles with coil or leaf springs? - ANSWER No, the springs or other suspension parts may require replacement.
What do most vehicle manufacturers call for when doing wheel alignment adjustments? - ANSWER Vehicle unloaded and at a specific ride height.
What do some car makers specify when adjusting wheel alignment? - ANSWER Precise weight loads to be placed during alignment.
What are six different ways to adjust front and rear camber? - ANSWER Shims placed between various suspension components and the frame; Eccentric cam lobe turned to move the control arm pivot point inward or outwards on the chassis; Adjusting sleeves on the control arm linkage; Adjusting strut rods; Moving strut mounts; Loosening and repositioning control arm mounting brackets on the frame.
Where can you get wheel alignment specifications? - ANSWER Vehicle manufacturers and computerized alignment equipment.
Does road crown affect the way a vehicle is cambered? - ANSWER Yes.
Does road crown affect the way a vehicle caster is set? - ANSWER Yes.
What should you do before adjusting camber and caster? - ANSWER Jounce the vehicle to relieve any binding or stress on suspension parts and let it settle at its normal ride height.
Does changing caster affect the camber adjustment? - ANSWER Yes.
Does changing camber affect the caster adjustment? - ANSWER Yes.
What should you do when changing camber or caster? - ANSWER When either is adjusted, check the other because changing one affects the other.
When is front wheel toe angle adjusted? - ANSWER After caster and camber adjustments are finished.
Should the camber angle still be checked even though camber may not adjustable? - ANSWER Yes.
Do most manufacturers publish specifications for the steering axis inclination? - ANSWER Yes.
What is SAI (Steering Axis Inclination)? - ANSWER The angle through the upper and lower ball joints or other pivot points compared with actual vertical.
What is "included angle"? - ANSWER Combination of SAI and camber.
How do you calculate included angle with positive camber, and with negative camber? - ANSWER Positive camber is added to SAI, negative camber is subtracted.
Can you determine if suspension parts are worn or damaged by comparing camber measurements to SAI and included angle specifications? - ANSWER Yes.
How is the caster angle of front wheels measured? - ANSWER Turning the front wheels a specified number of degrees left and right on the turn plates of the alignment rack.
[Show More]