SA1
Configure a static route from R3 to redirect all traffic to R1. Use next-hop ip address. Use the
router prompt below.
ipv6 route ::/0 2001:DB8:CAFE:A003::1
Refer to the diagram below. What commands will change th
...
SA1
Configure a static route from R3 to redirect all traffic to R1. Use next-hop ip address. Use the
router prompt below.
ipv6 route ::/0 2001:DB8:CAFE:A003::1
Refer to the diagram below. What commands will change the next-hop address for the
10.0.0.0/8 network from 172.16.40.2 to 192.168.1.254?
3 and 5 sagot ko - j
Configure a static route from R3 to redirect all traffic to R2 with administrative distance 2.
Use the next-hop ip address. Use the router prompt below.
ipv6 route ::/0 2001:DB8:CAFE:A002::1 2
Ipv4 : S* ⇐=> ipv6 : _______
Refer to the diagram. You are currently working on router 2 with the prompt below. If you
want to determine the ip address assigned to its interfaces and want to know the status of
the interface and protocols assigned to it, what command are you going to use?
Question 7
A network administrator is currently working on a cisco router and has no idea of the topological map of
the network. If he wants to see the directly connected cisco devices, what command will he execute?
Use the prompt below:
Router#
Question 8
A network administrator is experiencing external web pages taking longer than normal to load.The web
page does eventually load on the machine. Which troubleshooting commands can be used with to locate
where the issue is in the network?
Question 9
A network administrator is currently troubleshooting a cisco router. If he wants to verify the operational
status and IP address of an interface, what command will be used?
Use the prompt below:
Router(config)#
Do show ip interface brief
Where should the default static route be configured in the given topology?
R1
If you are to execute tracert 192.168.2.5 from pc1, what will be the first ip address listed on
the tracert table?
172.16.3.1
Where should the default static route be configured in the topology?
HQ
Question 13
What do you call a network that runs both IPv4 and IPv6 routing protocols?
Dual-stack
Configure a summary static route on isp router to reach the company network. Use the
router prompt below.
ip route 192.168.40.0 255.255.255.0 209.165.202.158
Question 15
Analogy:
_____ : Open <==> CDP : Cisco
LLDP
Question 16
A network administrator is currently working on a cisco router and has no idea of the topological map of
the network. If he wants to see all the directly connected devices regardless of the vendor, what
command will he execute? Use the prompt below:
Router#
Show LLDP neighbors
Question 17
When wireless client is not connecting, which of the following can be checked?
Verify that the PC has received an IP address via DHCP or is configured with a static IP address.
Connect the device to the wired LAN and ping a known IP address.
If necessary, reload drivers as appropriate for the client.
Check the channel settings on the wireless client.
Refer to the diagram. If standard static route is configured on r2. How many s can be seen
on the routing table?
3
Refer to the diagram. If you run the command below, assuming that the ip address is active
on the network, how many hops (number only) can be seen on the output considering the
s0/1/1 on r1 is administratively down?
4 W
hat are the different ways network router can learn its routes?
Refer to the diagram. You want to test the floating static route is working between r1 and r2
lan host using the 10th usable ipv6. Using the router prompt below. How will you do it?
Do show ipv6 route static | begin ::
Hey: ping 2001:db8:acad:2::/64
Refer to the diagram. You are currently working on router 3 with the prompt below and want
to verify only ipv6 static routes in the routing table. What command will you typed-in?
do show ipv6 route
Create a standard static route entry on r3 to a lan on r1 using the next-hop ip address. Use
the router prompt below.
Ip route 172.16.3.0 255.255.255.0 192.168.1.2
Question 24
Analogy:
OSPFv2 : Link State <==> BGP-4 : _________
Path Vector
tracert 172.16.3.2
Create a default static route on r3 to r2 using the next-hop ip address. Use the router
prompt below.
Ip route 0.0.0.0 0.0.0.0 192.168.1.2
Refer to the diagram. Configure a fully specified static route from r3 going to the r2 lan. Use
the router prompt below.
Ip route 172.16.1.0 255.255.255.0 s0/1/1 192.168.1.2
Choice 1 and 2
Refer to Figure. Your objective is provide connectivity between the 192.168.1.0/24 and
10.0.0.0/8 networks. Which command(s) will accomplish your task?
Unselect local router exit interface ip address ←
What are the options that you can use to configure static ip routing?
As you troubleshoot configuration, you noticed that the there is an incorrect configuration on r2.
Your tasked to remove the incorrect configuration. Use the router prompt below:
no ip route 172.16.3.0 255.255.255.0 192.168.1.1
You are currently working on r1 and want to ping the r2 lan interface from r1 lan interface. Use
the router prompt below.
Do ping ipv6 2001:DB8:CAFE:A001::2
You are currently working on r1 and want to ping the r2 lan interface. Use the router prompt
below.
hey: do ping ipv6 2001:DB8:CAFE:2::1
Which of the following applies to wireless Lan controller configuration procedures?
[Show More]
