MODULE 1
1. Heating the above the transformation ranges, usually 1300⁰ to 1350⁰ and
cooling slowly to soften the metal and increase in machining.
a. Annealing
b. Hardening
c. Normalizing
d. Tempering
2. Heating ab
...
MODULE 1
1. Heating the above the transformation ranges, usually 1300⁰ to 1350⁰ and
cooling slowly to soften the metal and increase in machining.
a. Annealing
b. Hardening
c. Normalizing
d. Tempering
2. Heating above the transformation temperature and quenching usually in
oil, for the purpose of increasing the hardness:
a. Annealing
b. Hardening
c. Normalizing
d. Tempering
3. Reheating to a temperature below the transformation range, followed by
any desired rate of cooling to obtain the desired properties of the metal.
a. Annealing
b. Hardening
c. Tempering
d. Stress relieving
4. Heating to a subcritical temperature about 1,100⁰F to 1,300⁰F and holding
at that temperature for suitable time for the purpose of reducing internal
residual stresses.
a. Annealing
b. Hardening
c. Tempering
d. Stress relieving
5. Heating to some 100⁰F above the transformation range with subsequent
cooling to below that range in still air at room temperature to produce uniform
structure of the metal.
a. Annealing
b. Hardening
c. Normalizing
d. Tempering
6. A machine tool used for producing holes in metal by the use of a cutting
tool called drill.
a. Drilling machine
b. Bring machine
c. Milling machine
d. Broaching machine
7. A machine tool used to from metal parts by removing metal from a
workpiece by the use of a revolving cutter with many teeth each tooth having
a cutting edge which removes its share of the stock.
a. Drilling machine
b. Boring machine
c. Milling machine
d. Broaching machine
8. A machine tool used to sharpen or shape tools by using an abrasive
wheel.
a. Tool grinder
b. Sharper
c. Planer
d. Power saw
9. A machine tools used to enlarge a hole by means of an adjustable cutting
tool with only one cutting edge.
a. Drilling machine
b. Boring machine
c. Milling machine
d. Broaching machine
10. A machine tool used to cut metal parts of light, medium and large
sections using a reciprocating hacksaw blade
a. Tool grinder
b. Sharper
c. Planer
d. Power saw11. A machine tool used to machine flat or plane surfaces with a single point
cutting tool.
a. Tool grinder
b. Shaper
c. Planer
d. Power saw
12. A machine tool used for production of flat surfaces on pieces too large or
too heavy hole in a sharper:
a. Tool grinder
b. Shaper
c. Planer
d. Power saw
13. A machine tool used to finish internal or external surfaces, such as holes
or keyways by the use of a cutter called a branch, which has a series of
cutting tool edges or teeth.
a. Drilling machine
b. Boring machine
c. Milling machine
d. Broaching machine
14. An alloy of copper and tin.
a. Brass
b. Bronze
c. Iron
d. Tin
15. An alloy of copper and zinc.
a. Brass
b. Bronze
c. Iron
d. Tin
16. The process of forming metal parts by the use of dies after the metal is
heated to its plastic range.
a. Rolling
b. Forging
c. Turning
d. Casting
17. The process of forming a metal parts by the use of a powerful pressure
from a hammer or press to obtain the desired shape, after the metal has
been heated to its plastic range.
a. Rolling
b. Forging
c. Turning
d. Casting
18. A manganese steel containing approximately 0.20% carbon.
a. SAE 1320
b. SAE 1230
c. SAE 2340
d. SAE 4230
19. A machine tool in which metal is removed by means of a revolving with
many teeth, each tooth having a cutting edge which remove its share of the
stock.
a. Milling machine
b. Broaching machine
c. Lathe machine
d. Boring machine
20. A metal turning machine tool in which work the work while revolving on
horizontal axis, is acted upon by cutting tool which is made to move slowly
(fee) in a direction more or less parallel to the axis of the work (longitudinal
feed).
a. Milling machine
b. Broaching machine
c. Lathe machine
d. Boring machine21. A machine tool used in the production of flat surfaces on pieces too large
or too heavy or, perhaps too awkward to hold in a sharper.
a. Sharper
b. Planer
c. Tool grinder
d. Power saw
22. It consists of shaping a piece by bringing it into contact with a rotating
abrasive wheel.
a. Drilling
b. Boring
c. Grinding
d. Broaching
23. A tool used in measuring diameter.
a. caliper
b. nanometer
c. tachometer
d. pyrometer
24. Used to true and align machine tools, fixtures, and works, to test and
inspect size trueness of finished work, and to compare measurements either
heights or depths or many other, measurement.
a. dial gauge
b. dial indicator
c. tachometer
d. speedometer
25. The ability of metal to be deformed considerably without rupture.
a. docility
b. plasticity
c. malleability
d. elasticity
26. The shop term used to include the marking or inscribing of center points,
circle, arcs, or straight lines upon metal surfaces, either curved or flat, for the
guidance of the worker.
a. shaping
b. hobbling
c. laying out
d. shaping
27. An operation of sizing and finishing a hole by means of cutting tool
having several cutting edges.
a. notching
b. piercing
c. turning
d. reaming
28. The operation of making a cone-shaped enlargement of the end of a
hole, as for recess for a flat head screw.
a. countersinking
b. knurling
c. squaring
d. perforating
29. The operation of enlarging a hole of means of an adjustable cutting tool
with only one cutting edge.
a. drilling
b. broaching
c. milling
d. boring
30. An imaginary circle passing through the points of which the teeth of the
meshing gears contact each other.
a. pitch circle
b. addendum circle
c. addendum circle
d. base circle31. A type of bolt intended for use in bolting wooden parts together or wood
to mental. It has a short portion of shank just underneath a round head,
which is designed to keep the bolt from turning in the wood when the nut is
tightened.
a. u-bolt
b. carriage bolt
c. eye bolt
d. stud bolt
32. The number of teeth per inch of pitch diameter and which gives some
indications of size of the gear teeth.
a. module
b. pitch circle
c. diametral pitch
d. circular pitch
33. The distance from the center of one tooth of gear to the center of the next
consecutive tooth measured on the pitch.
a. circular pitch
b. module
c. diametral pitch
d. pitch circle
34. The portion of gear tooth that projects above or outside the pitch circle.
a. top relief
b. dedendum
c. addendum
d. tooth space
35. The portion of the gear tooth space that is cut below the pitch circle and
is equal to the addendum plus the clearance.
a. top root
b. dedendum
c. addendum
d. top land
36. When meshed with a gear, it is used to change rotary motion to
reciprocating motion.
a. gear shaft
b. gear tooth
c. gear rack
d. gear motor
37. A kind of gear used for heavy duty works where a large ratio of speed is
required and are extensively used in speed reducers.
a. bevel gears
b. worm gears
d. helical gears
d. spiral gears
38. A kind of gears used to transmit motion from one shaft to another shaft at
an angle to the first.
a. bevel gears
b. worm gears
c. helical gears
d. spiral gears
39. The uniform heating of steel above the usual hardening temperatures,
followed by cooling freely in air.
a. annealing
b. normalizing
c. hardening
d. tempering
40. The operation of cooling a heated of work rapidly by dipping it in water,
brine or oil.
a. quenching
b. tempering
c. normalizing
d. annealing41. A method used in softening a piece of metal that is too hard to machine
and is done by heating steel slowly above the usual hardening temperature,
keeping it at the heat for ½ to 2 hours, then cooling slowly, preferably in a
finance.
a. broaching
b. quenching
c. normalizing
d. annealing
42. The total permissible variation in the size of a dimension; the difference
between the limits of size.
a. allowance
b. tolerance
c. variance
d. interface
43. The operation of machine the end of a work piece to make the end
square with axis.
a. squaring
b. buffing
c. lapping
d. honing
44. The clearance between the tooth profiles of a gear tooth.
a. toothspace
b. backlash
c. flank
d. width
45. A mechanism which usually do the indexing in a machine tool.
a. slotter
b. chuck
c. diving head
d. indexer
46. A material that can wear away a substance softer that itself.
a. phenol
b. abrasive
c. tungsten
d. chromium
47. A cylindrical bar of steel with threads formed around it and grooves or
flutes running lengthwise in it, intersecting with the threads to form cutting
edges. It is used to cut internal threads.
a. groove
b. lap
c. tap
d. flute
48. A set of gages consisting of thin strips of metal of various thicknesses
mounted in a steel case or holder and is widely used for measuring and
checking clearances.
a. feeler gage
b. depth gage
c. line center gage
d. lay-out gage
49. A machine tool which is very similar to a shaper except that the ram
reciprocates vertically rather than horizontally.
a. lathe
b. grinder
c. planer
d. slotter
50. A machine tool used principally to machine flat or plane surfaces with
single-point cutting tool.
a. grinder
b. shaper
c. planer
d. turret lathe51. A kind of bolt which has no head an instead has threads on both ends.
a. Stud bolts
b. acme threaded bolts
c. square threaded bolts
d. hex bolts
52. A kind of chuck which has reversible jaws which could b adjusted
separately.
a. collet chuck
b. independent chuck
c. four jaw chuck
d. two jaw chuck
53. A tool which when pressed into a finished hole in a piece of work
provides centers on which the piece may be turned or otherwise machined.
a. mash
b. butt
c. mandrel
d. wobble
54. A kind of chuck which should not be used where extreme accuracy is
required.
a. collet chuck
b. magnetic chuck
c. for jaw chuck
d. universal chuck
55. The process of checking or producing checkers on the surface of a piece
by rolling checkered depression into the surface.
a. knurling
b. hemming
c. breading
d. embossing
56. It fits into the main spindle of a lathe and is so called because it as act a
bearing surface on which the work rests. It revolves with the work. When
compared with hardness of the dead center in the tailstock, it is usually soft,
and is so made since it does no work.
a. ram center
b. spindle center
c. live center
d. bearing center
57. A gripping device with two or more adjustable jaws set radially.
a. chuck
b. carriage
c. tailstock
d. fan
58. Steel balls for ball bearing are manufactured by:
a. turning
b. rolling
c. casting
d. cold heading
59. Addendum of cycloidal gear tooth is:
a. cycloid
b. epicycloids
c. straight rack
d. in volute
60. In a lathe, it comprises the main spindle, the necessary mechanism for
obtaining the various spindle speed and also certain gears which are used to
operate the quick change gear mechanism.
a. headstock
b. carriage
c. tailstock
d. fan61. The process of heating a piece of steel to a temperature within or above
critical rage and cooling rapidly.
a. normalizing
b. hardening
c. annealing
d. tempering
62. Welding operation in which a non-ferrous filler metal melts at a
temperature below that of the metal joined but is heated above 450c
a. gas welding
b. spot welding
c. brazing
d. steam welding
63. Uniting two pieces of metal by means of different metal which is applied
between the two in molten state.
a. carling
b. welding
c. soldering
d. brazing
64. Fusion process in which the metal is heated into a state of fusion
permitting it to flow together into solid joint.
a. electric arc welding
b. gas welding
c. spot welding
d. projection welding
65. Joining metal by means of high current at low voltage. During the
passage of current, pressure by the electrodes produces a forge weld.
a. spot welding
b. resistance welding
c. steam welding
d. gas welding
66. A device for accurately measurement diameters.
a. radiometer
b. profilometer
c. spectrometer
d. micrometer
67. A group of thin steel strips for measuring clearance.
a. distortion gage
b. feeler gage
c. line center gage
d. deflection gage
68. A hand tool used to measure engine crank web deflection.
a. distortion gage
b. feeler gage
c. line center gage
d. deflection gage
69. A hand tool used to measure tension on bolts.
a. indexer
b. torque wrench
c. torsionmater
d. tensiometer
70. The permissible variation in the size of a dimension: the difference
between the limits of size.
a. allowance
b. variance
c. clearance
d. tolerance
71. A gear with teeth on the outer cylindrical surface.
a. outer gear
b. external gear
c. spiral gear
d. helical gear72. The diameter of a circle coinciding with the top of the teeth of an internal
gear.
a. pitch diameter
b. root diameter
c. internal diameter
d. central diameter
73. A circle coinciding with a tangent to the bottom of the spaces.
a. root circle
b. pitch circle
c. addendum circle
d. dedendum circle
74. The total depth of the tooth spaces, equal to addendum plus dedendum.
a. full depth
b. working depth
c. whole depth
d. dedendum
75. The depth of tooth space below the pitch circle.
a. dedendum
b. working depth
c. full depth
d. tooth depth
76.The of gear teeth to each mm pitch diameter.
a. diameter pitch
b. module
c. circular pitch
d. English module
77. A machine tool in which abrasive wheel is used as cutting tool to obtain a
very smooth finish.
a. drill
b. grinder
c. planer
d. shaper
78. It is used to produce a verily of surfing by using a circular-type cutter with
a multiple teeth.
a. grinding machine
b. shaper
c. drilling machine
d. milling machine
79. It is used principally to machine flat or plane surfaces with a single point
tool.
a. drill
b. shaper
c. planer
d. tool grinder
80. Cutting a hole by means of rotating tool or the work may revolve and to
the tool remain fixed as the lathe.
a. piercing
b. notching
c. boring
d. perforating
81. One of the following is not a tap used for cutting threads in holes.
a. tapping tap
b. plug tap
c. taper tap
d. bottoming top
82. An index or dividing head.
a. a part of a drill press
b. used to rotate the work
c. not used to cut helixes
d. always manually operated83. Galvanized iron is a term referring to iron coated with:
a. tin
b. zinc
c. magnesium
d. aluminum
84. The moment of inertia of a rectangle whose base is “b” and height “h”
about base is:
a. bh3/12
b. bh/36
c. bh3/3
d. bh2/4
85. In usual spur gearing:
a. the pitch circle and the base circle are the same
b. working depth includes the clearance
c. tooth outline are usually involute curves
d. tooth outline are always cycloidal curves
86. A stainless steel is obtained principally by the use of the following
alloying element.
a. chromium
b. tungsten
c. carbon
d. phenol
87. One of the following is not a common term relating to the classification of
fits.
a. tunking
b. snug
c. medium force fit
d. bound
88. Herringbone gears are gears which:
a. do not operate on parallel shaft
b. have a line of contact between the teeth
c. consist of two left handed helical gears
d. tend to produce thrust on the shaft
89. Internal stresses existing in a welded connection:
a. are not relieved when the weld is peened
b. are not relieved by heat treatment
c. may be relieved when the weld is peened
d. are relieved by x-ray analysis
90. In general the design stress and factory of safety are related as follows:
a. design stress = ultimate stress times factor of safety
b. design stress = ultimate stress divided by factor of safety
c. design stress = design stress divided by factor of safety
d. design stress = factor stress divided by design of safety
91. A group thin steel strips for measuring clearances.
a. depth gage
b. feeler gage
c. lay out gage
d. clearance gage
92. A hand tool used to measure tension on bolts.
a. indexer
b. torsionmeter
c. torque wrench
d. tensiometer
93. A material that can wear way a substances softer that itself.
a. abrasive
b. corrosive
c. tungsten
d. alloy94. The material used in high speed processes.
a. high speed steel
b. chromium
c. cast iron
d. carbon steel
95. An alloy of copper and zinc.
a. chromium
b. bronze
c. brass
d. aluminum
96. An alloy of copper, tin and small amount of phosphorous.
a. chromium
b. bronze
c. brass
d. aluminum
97. The process of working metals of the application of sudden blows or by
steady pressure.
a. welding
b. extrusion
c. forging
d. swaging
98. A welding operation in which a non-ferrous filler metal melts at a
temperature below that of the metal joined but is heated above 450 C°
a. brazing
b. spot welding
c. gas welding
d. projection welding
99. The operation of cooling a heated piece of work rapidly by dipping it in
water, brine or oil.
a. tempering
b. annealing
c. quenching
d. normalizing
100. A machine tool used to machine flat surfaces.
a. shaper
b. planer
c. grinder
d. latheMODULE 2
1. A machine tool in which an abrasive wheel is used as a cutting tool to
obtain a very smooth finish.
A. planer
B. shaper
C. power saw
D. grinder
2. It is used to produce a variety of surfaces by using a circular type cutter
with multiple teeth.
A. milling machine
B. broaching machine
C. beading machine
D. hemming machine
3. A heavy rotating body which serves as reservoir for absorbing
anddisturbingkinetic energy.
A. shaft
B. governor
C. flywheel
D. puncher
4. A kind of gear used for heavy duty works where a large ratio of speed is
required and are extensively used in speed reducers.
A. helical gear
B. worm gear
C. bevel gear
D. spiral gear
5. A kind of gear used to transmit motion from one shaft to another shaft at
angle to the first.
A. helical gear
B. worm gear
C. bevel gear
D. spiral gear
6. The minimum thickness of steel members exposed to weather and
accessible for painting is.
A. 6mm
B. 8mm
C. 4mm
D. 10mm
7. The common deoxidizer and cleanser of steel, forming oxides and
sulfates, which are carried off in the slag.
A. manganese
B. carbon
C. tungsten
D. sulfur
8. A highly transparent and exceedingly hard crystalline stone of almost pure
carbon.
A. carbon
B. diamond
C. bronze
D. crystalline
9. A fine grained, salty silica rocks use for sharpening edge tools.
A. eutectoid
B. austenite
C. oilstone
D. pearlite
10. An amorphous solid made by fusing silica with a basic oxide.
A. pearlite
B. rock
C. silicon
D. glass11. A soft yellow metal, known since ancient times a precious metal which all
materials values are based.
A. solidus
B. bronze
C. gold
D. austenite
12. The operation of cooling a heated piece of work rapidly by dropping it to
water, brine or oil.
A. quenching
B. annealing
C. squeezing
D. normalizing
13. A device used to prevent leakage of media.
A. seal
B. packings
C. teflon
D. graphite
14. A welding operation in which a non-ferrous filler metal melts as a
temperature below that of the metal joined but is heated above 450’C.
A. arc welding
B. brazing
C. spot welding
D. bult welding
15. The process of working metals by the application of sudden blows or by a
steady pressure.
A. trimming
B. welding
C. forging
D. lancing
16. The process of producing a variety of surfaces by using a circular type
cutter with multiple teeth.
A. piercing
B. cutting
C. embossing
D. milling
17. The softening of metal by heat treatment and most commonly consists of
heating the metal up to near molten state and then cooling them very slowly.
A. quenching
B. tempering
C. annealing
D. forming
18. The maximum stress induced in a material when subjected to alternating
or repeated loading without causing failure.
A. elastic limit
B. proportional limit
C. rupture strength
D. endurance limit
19. The total deformation measured in the direction of the line of stress.
A. axial deformation
B. elongation
C. strain
D. unit stress
20. The maximum stress to which a material can be subjected without a trace
of any permanent set remaining upon a complete withdrawal of the stress.
A. ultimate limit
B. proportional limit
C. endurance limit
D. elastic limit21. The total permissible variation in the size of a dimension: the difference
between the limits of the size.
A. deformation
B. variance
C. tolerance
D. allowance
22. Fluid film desired between two surfaces having relative sliding motion.
A. lube oil
B. lubrication
C. graphite
D. grease
23. Flexible material used to seal pressurized fluids, normally under dynamic
conditions.
A. packings
B. teflon
C. seals
D. safety shield
24. A total resistance that a material offers to an applied load.
A. flexure
B. stress
C. elasticity
D. rigidity
25. A property of material which relates the lateral strains to the longitudinal
strain.
A. rigidity
B. Elasticity
C. Poisson’s ratio
D. deflection
26. A kind of gear used for heavy duty works where a large ratio of speed is
required and is extensively used in speed reducers.
A. spiral gear
B. bevel gear
C. worm gear
D. helical gear
27.A kind of gear used to transmit motion from one shaft to another shaft at
an angle to the first
A. spiral gear
B. worm gear
C. helical gear
D. bevel gear
28. Which of the following is not a classification of iron ore?
A. hamadite
B. magnetite
C. sulfurite
D. siderite
29. Which of the following metals will respond to heat treatment?
A. cast iron
B. medium carbon steel
C. wrought iron
D. low carbon steel
30. Which of the following is a non-magnetic?
A. cast iron
B. alloy steel
C. cast steel
D. manganese steel
31. The ability of metal to withstand loads without breaking down is:
A. stress
B. strength
C. strain
D. elasticity32. A machining operation whereby the tool reciprocates and the feed is
stationary is called:
A. shaping
B. reaming
C. planning
D. turning
33. Any material that retards the flow of electricity used to prevent passage
or escape of electric current from conductors.
A. insulators
B. bricks
C. ceramics
D. refractories
34. A metallic element and the only metal that is liquid at ordinary
temperature.
A. austinite
B. mercury
C. manganese
D. martensite
35.An alloy of copper and zinc.
A. aluminum
B. bronze
C. brass
D. nickel
36.Usually a copper-tin alloy is.
A. aluminum
B. nickel
C. brass
D. bronze
37.A tool with hardened points used for scribing circles or laying of distances.
A. trammel
B. caliper
C. divider
D. micrometer
38.Name of mechanism which a welding operator holds during gas welding
and at the end of which the gases are burned to perform the gas welding
operations.
A. mash
B. core
C. wobble
D. torch
39.The maximum stress to which a material may be subjected before failure
occurs.
A. rupture stress
B. yield stress
C. ultimate stress
D. allowable stress
40. The maximum stress induced in a material when subjected to alternate or
repeated loading without causing failure.
A. yield point
B. ultimate point
C. endurance limit
D. proportional limit
41. Which of the following is not a classification of iron core?
A. hematite
B. magnetite
C. sulfurite
D. siderite
42. Which of the following metals which will respond to heat treatment?A. cast iron
B. wrought iron
C. medium iron
D. low carbon iron
43. Materials usually ceramics employed where resistance to very high
temperature is required as for furnace linings and melting spots.
A. refractories
B. gaskets
C. insulators
D. safety shield
44. The softening of metal by heat treatment and most commonly consist of
heating the metal up to near molten state and then cooling them very slowly.
A. annealing
B. hardening
C. normalizing
D. tempering
45. The process of producing a variety of surfaces by using a circular type
cutter with multiple teeth.
A. milling
B. drilling
C. broaching
D. boring
46.The process of working metals by the application of sudden blows or by a
steady pressure.
A. rolling
B. forging
C. casting
D. turning
47. A welding operation in which a non-ferrous filler metal melts as a
temperature below that of the metal joined but is heated above 450°C.
A. spot welding
B. gas welding
C. brazing
D. arc welding
48. The operation of cooling a heated piece of work rapidly by dropping it to
water, brine or oil.
A. Quenching
B. tempering
C. Annealing
D. normalizing
49. A machine tool in which an abrasive wheel is used as a cutting tool to
obtain a very smooth finish.
A. grinding machine
B. broaching machine
C. milling machine
D. boring machine
50. A machine tool principally to machine flat or surfaces with a single point
cutting tool.
A. shaper
B. planer
C. grinder
D. broaching machine
51. A tool used for measuring diameters.
A. micrometer
B. tachometer
C. pyrometer
D. caliper
52. The total permissible variation in the size of a dimension: the difference
between the limits of the size.
A. toleranceB. fits
C. allowance
D. clearance
53. The maximum stress to which a material can be subjected without a trace
of any permanent set remaining upon a complete withdrawal of the stress.
A. ultimate stress
B. rupture stress
C. elastic limit
D. proportional limit
54. Fluid film desired between two surfaces having relatives sliding motion.
A. lubrication
B. seal
C. packing
D. safety shield
55. A total deformation measured in the direction of the line of stress.
A. stress
B. strain
C. endurance limit
D. Poisson’s ratio
56. A kind of gear used for heavy duty woks where a large ratio of speed is
required and are extensively used in speed reducers.
A. worm gear
B. spiral gear
C. helical gear
D. bevel gear
57. A kind of gear used to transmit motion from one shaft to another shaft at
an angle to the first.
A. worm gear
B. spiral gear
C. helical gear
D. bevel gear
58. The area of the machine shop where metal is being melted to form a new
shape is:
A. welding area
B. mass production area
C. foundry area
D. tool and die
59. A machine used in shaping metal by means of abrasive wheel or removal
of metals with an abrasive is called.
A. planer
B. power saw
C. shaper
D. grinding machine
60. The ability of material or metal to resist being crushed is:
A. compressive strength
B. fatigue strength
C. torsional strength
D. bending strength
61. A machining operation whereby the tool rotates while the feed is
stationary.
A. shaping
B. milling
C. turning
D. reaming
62. A machining operation whereby the tool reciprocates and the feed is
stationary.
A reaming
B. planningC. shaping
D. turning
63. Which of the following metals is easy to chisel?
A. carbon
B. manganese steel
C. phosphorus
D. sulfur
64. Ferrous metals contain relatively large amount of:
A. carbon
B. manganese
C. phosphorus
D. sulfur
65. Which of the following is not a strength property of metals?
A. tensile strength
B. rocking strength
C. fatigue strength
D. torsional strength
66. Which of the following is not a kind of mandrel?
A. expansion mandrel
B. contraction mandrel
C. taper mandrel
D. gang mandrel
67.Which of the following is not a part of lathe machine?
A. tailstock
B. headstock
C. carriage
D. fan
68. The range of motor power in KW of a universal milling machine, max feed
movement 1270mm lengthwise, 355 mm lateral, 508 mm vertical is:
A. 11 to 15kw
B. 16to 21kw
C. 7.5to 10kw
D. 22 to 30kw
69.The motor power in kW of a punch press, 50.8mm hole diameter, 25.4mm
thickness, for soft steels:
A. 15kw
B. 21kw
C. 7.5kw
D. 30kw
70. The range of motor power in KW of a cylinder grinding machine 600 x 50
mm wheel size, 2400 to 4200 mm center distance is:
A. 11 to 15kw
B. 16to 21kw
C. 7.5to 10kw
D. 22 to 30kw
71. The motor power in kW of a forming or bending machine 1600mm width,
508 mm head movement is:
A. 7.5kw
B. 11kw
C. 15kw
D. 22kw
72. The range of motor power in KW of an Engine lathe machine, average
service 1000mm to 1300mm swing.
A. 11 to 15kw
B. 7.5 to 10kw
C. 16 to 21kw
D. 22 to 30kw
73. A machine which can flatten surfaces on a horizontal, vertical or angular
plane.
A. shaper
B. planer
C. power saw
D. tool grinder74. The ability of metal to withstand forces thus the following a number twist.
A. shear strength
B. bearing strength
C. endurance limit
D. deformation
75.A property of material which relates the lateral strain to the longitudinal
strain.
A. stress
B. modulus of elasticity
C. Poisson’s ratio
D. deformation
76. A total resistance that a material offers to an applied load,
A. friction force
B. stress
C. rigidity
D. compressive force
77. A total deformation measured in: the direction of the line of stress.
A. strain
B. elasticity
C. elongation
D. contraction
78.An alloy element copper-tin alloy.
A. aluminum
B. brass
C. bronze
D. chromium
79. A metallic element of copper-tin alloy.
A. aluminum
B. brass
C. bronze
D. chromium
80. A metallic element and only metal that is liquid at ordinary temperature.
A. aluminum
B. mercury
C. zirconium
D. zinc
81. Any material that retard the flow of electricity, used to prevent passage or
escape of electric current from conductors.
A. refractory
B. ceramics
C. coating materials
D. insulator
82. The maximum stress to which a material may be subjected before failure
occurs.
A. rupture strength
B. ultimate strength
C. yield strength
D. proportional strength
83.The maximum stress induced in a material when subjected to alternating
or repeated loading without causing failure.
A. rupture strength
B. ultimate strength
C. endurance limit
D. proportional strength
84. Fluid film desired between two surfaces having relatives sliding motion
A. lubrication
B. seal
C. packing
D. safety shield85.The ability of metal to withstand loads with our breaking down.
A. strength
B. elasticity
C. rigidity
D. deformation
86. Materials usually ceramics employed where resistance to very high
temperature is required, as for furnace linings and metals melting pots.
A. insulators
B. gaskets
C. packings
D. refractories
87.An alloying element used principally to produce stainless steel.
A. aluminum
B. brass
C. bronze
D. chromium
88.A coating material used to produce galvanized iron.
A. zirconium
B. zinc
C. aluminum
D. chromium
89. A group of thin steel strips used for measuring clearances:
A. feeler gage
B. tachometer
C. micrometer
D. caliper
90.A hand tool used to measured tension in volts.
A. torque wrench
B. tachometer
C. shaver
D. tensor
91. Ratio of pitch diameter to the number of teeth.
A, diameter pitch
B. module
C. contact ratio
D. helical overlap
92. A circle the radius of which is equal to the distance from the gear axis to
the pitch point.
A. pitch circle
B. root circle
C. base circle
D. outside circle
93. A circle coinciding with a tangent to the bottom of the tooth spaces.
A. pitch circle
B. root circle
C. base circle
D. outside circle
94. The method of cold working by compression.
A. broaching
B. lapping
C. piercing
D. reaming
95. A machine tool used to finish internal and external surfaces by the use of
a cutter called a broach, which has a series of cutting edges or teeth.
A. lathe machine
B. broaching machine
C. planer
D. shaper
96. A cutting tool which has made to move slowly while acting on the work
which is revolving on a horizontal axis.
A. lathe machine
B. broaching machine
C. planer
D. shaper97. A machine tool used to produce variety of surfaces by using a circular
type cutter with multiple teeth.
A. lathe machine
B. milling machine
C. broaching machine
D. grinding machine
98. Used in production of flat surfaces on piece too large or too heavy to hold
in a shaper.
A. planer
B. shaper
C. grinder
D. shaver
99. Used to machine flat in curved surfaces with a tool which moves in a
reciprocating motion.
A. planer
B. shaper
C. grinder
D. shaver
100.A material that can wear away a substance softer that itself.
A. abrasive
B. tungsten
C. carbon
D. corrosive
MODULE 3
1. A tool with hardened steel points used for scribing or laying of
distances.
A. Plain scriber
B. Divider
C. Trammel
D. Hermaphrodite
2. A machine tool used principally to machine flat or plane surfaces with
a single pointed tool.
A. Shaper
B. Planer
C. Drill
D. Power Saw
3. A machine tool in which an abrasive wheel is used as a cutting tool to
obtain a very smooth finish.
A. Broaching Machine
B. Planer
C. Tool Grinder
D. Milling Machine
4. The process of working metals by the application of sudden blows or
by steady pressure.
A. Casting
B. Turning
C. Forging
D. Rolling
5. The operation of cooling a heated piece of work rapidly by dipping it in
water, brine or oil.
A. Quenching
B. Annealing
C. Tempering
D. Normalizing
6. The softening of metal by heat treatment and most commonly consist
of heating the metal up to near molten state and then cooling it very
slowly.
A. Annealing
B. Indexing
C. Knurling
D. Soldering7. Fluid film desired between surfaces relative sliding motion.
A. lube oil
B. Lubrication
C. Grease
D. graphite
8. A kind of gear used to transmit motion from one shaft to another shaft
at an angle to the first.
A. worm gear
B. bevel gear
C. helical gear
D. spur gear
9. The principal material used in high production metal working tools.
A. hyper-eutectoid
B. high speed steel
C. Lead
D. high speed carbon
10. A heavy rotating body which serves as a reservoir for absorbing and
redistributing kinetic energy.
A. Flywheel
B. Governor
C. Shaft
D. Puncher
11. A machine used in shaping metal by means of an abrasive wheel or
the removal of metals with an abrasive is called:
A. planer machine
B. power saw
C. shaper machine
D. grinding machine
12. Which of the following is not a part of lathe machine?
A. Tailstock
B. Fan
C. Carriage
D. Headstock
13. Which of the following is easy to chisel?
A. cast iron
B. alloy steel
C. cast steel
D. manganese steel
14. A machining operation whereby the tool reciprocates and the feed is
stationary is called:
A. Shaping
B. Reaming
C. Planning
D. Turning
15. Which of the following is not a kind of mandrel?
A. expansion mandrel
B. taper mandrel
C. contraction mandrel
D. foundry mandrel
16. The area of the machine shop where the metals is being melted to
form a new shape.
A. welding area
B. mass production area
C. foundry area
D. tool and die area
17. Which of the following is not used to temper steel.
A. brine salt bath
B. oil bath
C. water bath
D. steam bath
18. Which of the following is not a kind of cast iron?A. malleable iron
B. head iron
C. gray iron
D. white iron
19. The kind of center which is being attached and meshed to the
tailstock spindle which is also static while the work is rotating.
A. dead center
B. live center
C. focal center
D. work center
20. Which of the following is not a part of the headstock?
A. Spindle
B. Anvil
C. back gear
D. motor
21. Which process does not belong to the group?
A. vise grip
B. adjustable wrench
C. torque wrench
D. feeler gage
22. Which does not belong to the group?
A. Resistance welding
B. Soldering
C. Hardening
D. Brazing
23. Substances having sufficient carbon and or hydrogen for chemical
oxidation to produce exothermally, worthwhile quantities of heat.
A. Lubrication
B. Graphite
C. Grease
D. Fuels
24. A device that measures atmospheric pressure.
A. Piezometer
B. Hydrometer
C. Barometer
D. Odometer
25. The mass of the body per unit volume.
A. Volume flow rate
B. Density
C. Weight
D. Mass
26. Subjecting a substance to a high temperature below the fusion point,
usually to make it friable.
A. calcinations
B. fusion
C. boiling
D. Superheating
27. A special metal formed when two or more metals are melted
together.
A. Monel
B. Alloy
C. Solder
D. hastalloy
28. The ability of a moving body to perform work.
A. internal energy
B. potential energy
C. kinetic energy
D. flow work
29. Hardening the surface of iron-based alloys by heating them below
the melting point in contact with a carbonaceous substance.A. Carburizing
B. Normalizing
C. Martempering
D. Hardening
30. Any material that retard the flow of electricity, used to prevent or
escape of electric current from conductors.
A. Bricks
B. Insulators
C. Refractories
D. Ceramics
31. Material, usually ceramics, employed where resistance to very high
temperature is required, as a for furnace linings and metal melting pots.
A. Bricks
B. Insulators
C. Refractories
D. Ceramics
32. A device used to prevent leakage of media.
A. Packing
B. Safety shield
C. Gasket
D. Seals
33. The internal resistance a material offers to being deformed and is
measured in terms of applied load.
A. Strain
B. Elasticity
C. Stress
D. Resilience
34. The deformation that results from a stress and is expressed in terms
of the amount of deformation per inch.
A. Elongation
B. Strain
C. Poisson's ratio
D. Elasticity
35. The ability of the material to return to its original shape after being
elongated or distorted when the forces are released.
A. Elasticity
B. brittleness
C. Plasticity
D. Creep
36. The last point at which a material may be stretched and still return to
its undeformed condition upon release of the stress.
A. rupture limit
B. elastic limit
C. proportional limit
D. ultimate limit
37. The ratio of stress to strain within the elastic limit.
A. Creep
B. Modulus of rigidity
C. Modulus of elasticity
D. Poisson’s ratio
38. The ability of a metal to withstand forces that causes a member to
twist.
A. shear strength
B. tensile strength
C. bearing strength
D. torsional strength
39. The ability of material to resist being crushed.
A. tensile strengthB. shearing strength
C. compressive strength
D. torsion
40. The ability of metal to stretch, bend or twist without breaking or
cracking.
A. Elasticity
B. Ductility
C. Brittleness
D. Plasticity
41. The property of a material which resist forces action to pull the
material apart.
A. shear strength
B. tensile strength
C. compressive strength
D. bearing strength
42. The property of steel which resist indention or penetration.
A. Hardness
B. Elasticity
C. Ductility
D. none of these
43. In the color coding of pipe, the color for a pipeline of air is:
A. light blue
B. light orange
C. White
D. Gray
44. In the color coding pipe, the color for a pipeline of water is:
A. Light blue
B. Green
C. Brown
D. Silver gray
45. In the color coding of pipe, the color for pipeline of steam is:
A. Light orange
B. White
C. Silver gray
D. Light blue
46. The color for a pipeline of electricity in the color coding of pipe is:
A. light orange
B. white
C. silver gray
D. light blue
47. In the color coding of pipe, the color for pipeline of communication is:
A. light blue
B. White
C. Brown
D. light orange
48. The color of pipeline of fuel oil in the color coding of pipeline is:
A. light blue
B. brown
C. white
D. light orange
49. For high speed application the minimum number of teeth in small
sprocket should be:
A. 18 to 24
B. 26 to 30
C. 14 to 18
D. 24 to 28
50.The good deoxidizer in steel melting is:
A. Manganese
B. AluminumC. Silicon
D. all of these
51. In majority of machine members the damping capacity of the material
should be:
A. Zero
B. High
C. Low
D. Anything
52. For the moderate speed of mating gears, the ideal ratio of contact is:
A. 1.35-1.55
B. 1.0-1.3
C. 1.25-1.45
D. 1.25-4.0
53. The crest diameter of a screw thread is same as:
A. pitch diameter
B. minor diameter
C. major diameter
D. base diameter
54. For a high corrosion resistant stainless steel, what minimum
chromium content is required?
A. 8.0%
B. 4.5%
C. 1.5%
D. 8.5%
55. At quite low temperature (say-75%) the notched bar impact value of
steel.
A. increases significantly
B. decreases significantly
C. remain unchanged
D. depends on heat treatment
56. In order to realize the advantage of fluid friction, it is essential to
have:
A. no oil film
B. converging oil film
C. diverging oil film
D. parallel oil film in bearing
57. Zero axial thrust is experienced in:
A. herringbone gears
B. helical gears
C. bevel gears
D. worm gears
58. The maximum size of the fillet weld that can be made in single pass
is:
A. 3 mm
B. 6 mm
C. 7 mm
D. 4 mm
59. Muntz metal contains;
A. copper-aluminum
B. copper- tin
C. copper- nickel
D. Copper-zinc
60. Steel bars for ball bearings are manufactured by:
A. Cold heading
B. Casting
C. Rolling
D. Turning61. In general, alloys with high nickel content retain toughness to quite
low temperature up to:
A. -250°F
B. -360°F
C. -320°F
D. -240°F
62. Manganese steel standard designation is SAE____.
A. 8XXX
B. 10XX
C. 12XX
D. 13XX
63. A babbit is:
A. a cutectic of iron and iron phosphide
B. a gadget for measuring volume
C. a measure of magnetic induction produces in a material
D. antimony bearing lead or tin alloy
64. The minimum thickness of steel members exposed to weather and
accessible for painting is:
A. 4 mm
B. 6 mm
C. 8 mm
D. 10 mm
65. In a standard coarse thread bolt, the stress concentration is
maximum at:
A. all over the surface
B. Top surface
C. Root
D. Flank
66. Which of the following ropes are more flexible?
A. 6 to 19
B. 6 to 7
C. 8 by 19
D. 6 by 37
67. Tools usually used in wood pattern making in foundry shop.
A. band saw
B. saws and chisels
C. knives and drills
D. grinder
68. Type of bolt commonly used in the construction that is threaded in
both ends
A. hex bolt
B. stud bolt
C. square threaded bolts
D. eye bolt
69. Cast iron flywheels are commonly designed with factor of safety of:
A. 9 to 12
B. 8 to 11
C. 10 to 13
D. 7 to 10
70. Which of the type of chain is used in motorcycle?
A. Silent
B. Pintle
C. Bush holder
D. Long
71. Spiral gears are suitable for transmitting:
A. any power
B. small power
C. huge power
D. pulsating power
72. The type of cam used for low and moderate speed engines is
generally:
A. Flat
B. Involute
C. Tangent
D. Harmonic73. Gears for wrist watches are generally manufactured by:
A. Molding
B. Stamping
C. Galvanizing
D. Honing
74. The rated life of bearing changes:
A. inversely as cube of load
B. directly as load
C. inversely as square of load
D. inversely as load
75. The best material for brake drum is:
A. cast iron
B. Steel
C. Aluminum
D. Wrought iron
76. An electric body whose primary function is to deflect under load
A. Spring
B. Brake
C. Stopper
D. Clutch
77. Belt slip may take place because of:
A. loose load
B. heavy belt
C. driving pulley too small
D. all of the above
78. Rankine formula is valid up to slenderness ratio of:
A. 460
B. 480
C. 120
D. 150
79. In flange coupling the weakest element should be:
A. Flange
B. Key
C. Bolts
D. Shaft
80. Singe coupling is:
A. used for collinear shaft
B. used for non- collinear shafts
C. rigid coupling
D. flexible
81. Universal coupling is:
A. used for collinear shaft
B. used for non- collinear shafts
C. type of flange coupling
D. rigid coupling
82. In powder metallurgy the process of heating the cold pressed metal
powder is called:
A. Deposition
B. Granulation
C. Sintering
D. Precipitation
83. Which one is different from the remaining?
A. Nitriding
B. Cyaniding
C. Electroplating
D. Flame hardening
84. Splines are used when:
A. the power transmitted is low
B. the power to be transmitted is high
C. axial relative motion between shafts and hub is necessary
D. flame hardening85.Delta iron occurs at temperature of:
A. room temperature
B. above melting point
C. between 1400°C & 1539°C
D. between 1000°C & 1400°C
86. The most important element that controls the physical properties of
steel is:
A. Carbon
B. Silicon
C. Manganese
D. Tungsten
87. The process commonly used for thermo-plastic material is:
A. diecasting
B. injection moulding
C. shell moulding
D. cold forming
88. Select the one that has highest specific gravity?
A. Aluminum
B. Lead
C. Brass
D. High carbon steel
89. Age-hardening is related with:
A. Cast iron
B. Stainless steel
C. Duralumin
D. German silver
90. Foundry crucible is made of:
A. German silver
B. Lead
C. Mild steel
D. Graphite
91. Trimming is a process associated with:
A. Forging
B. machining of metals
C. Eloctroplating
D. Press work
92. A plug gauge is used to measure:
A. taper bores
B. cylindrical bores
C. spherical bores
D. screw threads
93. In arc welding operations the current value is decided by:
A. length of welded portion
B. voltage across the arc
C. size of the of electrode
D. thickness of plate
94. The phenomenon of weld decay takes place in:
A. Cast iron
B. Brass
C. Bronze
D. Stainless steel
95. Choose the one that will have highest cutting speed.
A. Aluminum
B. Brass
C. Bronze
D. Cast iron
96. Projection welding is:
A. continuous spot welding process
B. used to make mesh
C. multispot welding process
D. used to form97. Least shrinkage allowance is provided in case of which of the
following:
A. cast iron
B. Aluminum
C. white cast iron
D. brass
98. Dilatometer is used to find out which property of molding sand.
A. Permeability
B. Hot strength
C. Fineness
D. Moisture content
99. Cast alloy contains:
A. Copper
B. Nickel and copper
C. Copper and aluminum
D. Nickel and molybdenum
100. The maximum harden ability of the steel depends on:
A. the carbon content
B. the chemical composition
C. the grain size
D. the alloying elements present
MODULE 4
1. The hardness of steel increases if it contains:
A. Martensite
B. Pearlite
C. Austenite
D. All of the above
2. How do call a steel with 0.8% carbon and 100% peartile?
A. Austenite
B. Solidus
C. Hyper-eutectoid
D. Eutectoid
3. What is the range of the tensile strength of common varieties of cast
iron?
A. 40-60 Mpa
B. 150-180 Mpa
C. 840-500 Mpa
D. 1500-1650 Mpa
4. Fatigue failure occurs when a part is subjected to:
A. Compressive stress
B. Tensile stress
C. Torsional stress
D. Fluctuating stress
5. Paramagnetic alpha iron changes to gamma iron at what
temperature?
A. 440˚C
B. 910˚C
C. 970˚C
D. 1639˚C
6. The diameter of the washer is generally:
A. Equal to the diameter of the bolt
B. Slightly more than the diameter of the bolt
C. Slightly less than the diameter of the bolt
D. Of any size that suits the application
7. The compression members tend to buckle in the direction of:
A. Axis of load
B. Minimum cross-section
C. Least radius of gyration
D. Perpendicular to the axis of load8. A kinetic chain needs a minimum:
A. 2 links and 2 turning pairs
B. 3 links and 3 turning pairs
C. 4 links and 4 turning pairs
D. 3 links and 2 turning pairs
9. Which of the following pairs is formed if shaft is revolving in a
bearing?
A. Lower fair
B. Turning pair
C. Sliding pair
D. Cylindrical pair
10. How many links are there in a pantograph?
A. 3
B. 4
C. 5
D. 6
11. A pantograph is a mechanism having:
A. Lower pairs
B. Rolling pairs
C. Spherical pairs
D. Higher pairs
12. Which of the following describes the “slip” in belt drive?
A. Loss in power
B. Difference between the angular velocities of 2 pulleys
C. Difference between linear speed of the rim
D. Difference between the linear speed of the rim of pulley and the
belt on it.
13. Which of the following is the orientation of the axes of the two shafts
in cross helical worm?
A. Parallel
B. Non-parallel
C. Intersecting
D. Non-parallel and non-intersecting
14. In case of gears the addendum is given by:
A. 1 module
B. 2.16 x module
C. 1.57 x module
D. 1.25 / module
15. How do you call a cam where in the follower reciprocates or
oscillates in plane parallel to its axis?
A. Circular cam
B. Reciprocating cam
C. Cylindrical cam
D. Oscillating cam
16. How are gears for watches generally manufactured?
A. Die casting
B. Machining in hobber
C. Power metallurgy process
D. Stamping
17. Rope break dynamometer uses what?
A. Oil as lubricant
B. No lubricant
C. Grease as lubricant
D. Water as lubricant
18. Which of the following could be the effect of cold working?
A. Increases the fatigue strength
B. Decrease the fatigue strength
C. Has no influence on fatigue strength
D. None of these19. In testing a material for endurance strength, it is subjected to:
A. Completetly reverse load
B. Static load
C. Impact load
D. Dynamic load
20. Coaxing is athe procedure of increasing:
A. Metal strength
B. Metal hardness by surface treatment
C. Metal resistant to corrosion by coating
D. Fatigue limit by overstressing the metal by successively
increasing loadings
21. Up to what percent thikness of plate, edge preparation for welding is
not needed?
A. 2mm
B. 4mm
C. 8mm
D. 12mm
22. Arc blow take place in:
A. Gas welding
B. Arc welding when straight polarity is used
C. Arc welding when reverse polarity used
D. Welding stainless steel
23. What is the function clutch in the machine tools?
A. Alignment of drive
B. Lowering of drive
C. To insure that 2 shafts line up at high speed
D. To connect shaft so that the driven shaft will rotate with the
driving shaft and to disconnect them at all
24. The height of tooth above the pitch circle or the radical distance
between pitch circle and top land of the tooth.
A. Addendum
B. Dedendum
C. Top rooth
D. Top land
25. How do call the distance of the tooth which is equal to the sum of the
addendum and the dedendum?
A. Full depth
B. Working depth
C. Whole depth
D. Pitch
26. Which of the following stresses that is independent of loads?
A. Shear stress
B. Residual stress
C. Design stress
D. Yield stress
27. Which of the following is not used to resemble the shape of tool bit?
A. Thread cutting
B. Center cutting
C. Square nose
D. Round nose
28. What is the recommended best cutting angle of drill for work on steel
or cast iron?
A. 39 degrees
B. 49 degrees
C. 59 degrees
D. 29 degrees
29. Copper and most of its alloys can be hardened by which of the
following?
A. Cold working
B. Soaking
C. PatentingD. Case hardening
30. Types of V-belts to use in a driving pulley with speed of 360 rpm and
transmitting 5 Hp.
A. Type A belts
B. Type B belts
C. Type C belts
D. Type D belts
31. Which of the following is not an angle measuring device?
A. Bevel protector
B. Sine bar
C. Combination square
D. Angle iron
32. The mould for casting ferrous materials in continuous casting
process is made of what material?
A. Copper
B. Medium carbon steel
C. High carbon steel
D. Low carbon steel
33. Clutch slippage while clutch is engaged is especially noticeable:
A. During idling
B. A low speed
C. During acceleration
D. During brake
34. In general, to engaged securely and prevent dragging, what is the
clearance between releases bearing and release collar in the clutch?
A. 2 – 3 mm
B. 4 – 5 mm
C. 6 – 7 mm
D. 8 – 9 mm
35.Piston compression rings are made of what material?
A. Steel
B. Bronze
C. Aluminum
D. Cast iron
36. What is the usual value of helix angle of drill?
A. 120 degrees
B. 110 degrees
C. 60 degrees
D. 30 degrees
37. What is meant by drossing?
A. A method of cleaning the castling
B. An inspection method for castling
C. A method of deoxidation of molten metal
D. The formation of oxides on the molten metal surface
38. If the first digit in AISI and SAE designation is one (1), then, it
indicates what?
A. Carbon steels
B. nickel steels
C. molybdenum steels
D. Chromium steels
39. Which of the following where the gear toothvernier is used to
measure?
A. Module
B. Gear tooth profile
C. gear tooth thickness of gear tooth
D. pitch line thickness of gear tooth
40. A cold chisel is made of what?
A. Mild steel
B. German steel
C. High carbon steel
D. Cast iron41. It is the ability of a material to absorb energy when deformed
elastically and to return it when unloaded.
A. Creep
B. Fatigue strength
C. Resilience
D. Toughtness
42. Which of the following cams where the follower reciprocates or
oscillates in a plane perpendicular in a plane parallel to the axis of
rotation?
A. Cams curves
B. Radial cam
C. Cylindrical cam
D. Tangential cam
43. Which of the following cams where the follower reciprocates or
oscillates in a plane perpendicular its axis of rotation?
A. Tangential cam
B. Cam curves
C. Radial cam
D. Cylindrical cam
44. During tensile test, which of the following stress-strain curve(s) fits for
a glass rod?
A. A straight line
B. A parabola
C. An irregular curve
D. A sudden break
45. In case of a knuckle joint, the pin is most likely to fail in:
A. Shear
B. Tension
C. Compression
D. Double shear
46. A single ply leather belt running at a belt velocity of 300
ft /min is likely to transmit per inch of width:
A. 2.5Hp
B. 3.0 Hp
C. 4.0 Hp
D. 5.0 Hp
47. At what temperature range where ferromagnetic alpha iron exist?
A. Below 723 Celsius
B. 700-910 Celsius
C. 1000-1440 Celsius
D. Above 1593 Celsius
48. How do you call a body have identical properties all over?
A. Heterogeneous
B. Homogeneous
C. Elastic
D. Ductile
49. How is the material described if it recovers its original dimensions
when the load is removed?
A. Elastic
B. Plastic
C. Brittle
D. Malleable
50. What is tha percentage of carbon in Eutectoid steel?
A. 0.02%
B. 0.30%
C. 0.63%
D. 0.80%
51. The presence of sulfur in pig iron makes:
A. The casting unsound
B. It brittle
C. It hard
D. It is easy machinable52. What is the effect of alloying zinc to copper?
A. Increase hardness
B. Impart free-machining properties
C. Improve hardness and strength
D. Increase strength and ductility (if added up to 10-30%)
53. The imperfection in the crystal structure of metal is:
A. Impurity
B. Fracture slip
C. Slip
D. Dislocation
54. When is the pressure release in resistant welding?
A. After the weld cools
B. During heating period
C. After complition of current
D. Just at the time of passing of the current
55. If it is the thickness of sheet to be spot welded, then electrode tip
diameter is equal to___.
A. T2
B. 2 sq.rt. Of t
C. Sq. rt. Of t
D. 1.5 sq. rt. Of t
56. A twist drill is specified by which of the following?
A. Its shank and diameter
B. Shank, material and flute size
C. Its diameterang lip angle
D. shank, material and diameter
57.Which of the following is used to measure the clearance between the
value and tappet of an automobile engine?
A. Shape gauge
B. Slip gauge
C. Feeler gauge
D. Vernier scale
58. Speedometer drive is generally taken from:
A. Gear box
B. Fan belt
C. Flywheel
D. Front wheel
59. What is the usual percentage of cut on the return stroke of hacksaw
blade?
A. 0
B. 5
C. 7
D. 9
60. Which of the following will best describe sunk key?
A. The keyway is helical along shaft
B. The keyway is cut in hub only
C. The keyway is cut in shaft only
D. The key is cut in both shaft and hub
61. Which of the follwing where turn buckle has ?
A. Left hand threads on one end and right hand threads on other
end
B. Right hand threads on both ends
C. Left hand thraeads on both ends
D. No threads
62. Which of the following is the best process for butt welding of two
plates each of which is 25mm thick?
A. Electro slag welding
B. Gas welding
C. Sudmerged arc welding
D. Steam welding63. Which of the following statement(s) is correct for an oil less bearing:
A. The oil film is maintained by supplying oil under pressure.
B. The oil film pressure is produced only by rotation of the journal.
C. Do not need external supply of lubricant
D. Grease is needed to be applied after some intervals
64. The working load P for a chain for crane application is expressed in
terms of diameter of link “d” in cm as follows:
A. P = 1.5 d2
B. P = 25 d2
C. P = 50 d2
D. P = 500 d2
65. The column splice is used for increasing:
A. Cross-sectional area of the column
B. Length of the column
C. Strength of the column
D. All of the above
66. At what temperature those gamma irons exist?
A. Between 910˚C and 1400˚C
B. Between 1400˚C and 1539˚C
C. Near melting point
D. Room temperature
67. The behavior of metals where in strength of metal is increased and
the ductility is decreased on heating at a relatively low temperature after
cold working is called:
A. Clustering
B. Twinning
C. Screw dislocation
D. strain aging
68. Which of the following statement(s) is correct in “carbon steel
castings”?
A. The percentage carbon is less than 1.7%
B. The percentage carbon is between 1.7% to 2%
C. The percentage for alloying elements is controlled
D. None of the above
69. Aluminum alloys for pressure die casting:
A. Must not be free from hot shortness
B. Must have iron as one of the constituents
C. Must not possess considerable fluidity
D. Must be light
70. Which of the following is maximum in 18-4-1 high speed steel?
A. Tungsten
B. Chromium
C. Argon
D. Iron
71. Super conductors:
A. Exist at temperature below 10K
B. Are the dense metals without voids
C. Are non-metallic substances
D. Are the purest forms of metals
72. When large number of components are turned and parted off from a
bar, the chuck generally used is:
A. 2 jaw chuck
B. 4 jaw chuck
C. Collet chuck
D. Magnetic chuck73. Cutting speed for some materials are as under which one of the
following could be cutting speed for brass?
A. 30 m/min
B. 40 m/min
C. 80 m/min
D. 50 m/min
74. If V is the volume of metal in casting and A as its surface area, then
the time of solidification will be proportional to:
A. V2, 1/A
B. 1/V 2, A 2
C. V , 1/A 2
D. V 2, 1/A 2
75. The draft allowance on metallic pattern as compared to wooden ones
is:
A. More
B. Same
C. Less
D. More or less depending on size
76. Arc metal patterns are used for:
A. Precision castings
B. Small castings
C. Large castings
D. Large scale production of castings
77. What tool is used in foundry for repairing the mould?
A. Swab
B. Gagger
C. Bellows
D. Rammer
78. What tool is used in foundry for smoothening and cleaning out
depression in the mould?
A. Swab
B. Gagger
C. Bellows
D. Rammer
79. Which of the following does not have to be lubricated when drilling?
A. Brass
B. Steel
C. Monel
D. Mild steel
80. The tool used in precision work to smooth or enlarge holes is called
a:
A. Round out
B. Drift pin
C. Reamer
D. Protractor
81. When measuring a drill for size, measure across the:
A. Margins
B. Flutes
C. Shank
D. Point
82. How do you call the tool used for cleaning files?
A. File cleaner
B. File card
C. File oilstone
D. Scraper
83. The melting point of Babbitt is approximately:
A. 1000˚F
B. 650˚F
C. 750˚F
D. 500˚F84. How is tubing measured?
A. Inside diameter
B. Outside diameter
C. Thickness of wall
D. Wire gage
85. Which of the following metals will respond to heat treatment?
A. Cast iron
B. Wrought iron
C. Medium carbon steel
D. Low carbon steel
86. The ability of metal to withstand loads without breaking down is:
A. Stress
B. Strength
C. Strain
D. Elasticity
87. Which of the following metals is non-magnetic?
A. Cast iron
B. Alloy steel
C. Cast steel
D. Manganese steel
88. A machining operation whereby the tool reciprocates and the feed is
stationary.
A. Planning
B. Shaping
C. Turning
D. Reaming
89. Which of the following is not a tap used for cutting threads in holes?
A. Tapping tap
B. Plug tap
C. Taper tap
D. Bottoming tap
90. Herring bone gears are gears which:
A. Do not operate on parallel shafts
B. Have a line contact between the teeth
C. Consist of two left handed helical gears
D. Tend to produce thrust on the shafts
91. Which of the following statements is true for the internal stresses
existing in a welded connection?
A. Internal stresses are not relieved by heat treatment
B. Internal stresses are not relieved when weld is peened
C. Internal stresses may be relieved when weld is peened
D. Internal stresses are relieved by x-ray analysis
92. Stainless steel is obtained principally by the use of which of the
alloying elements?
A. Chromium
B. Nickel
C. Carbon
D. Tungsten
93. Galvanized iron is a term referring to iron coated with:
A. Tin
B. Zinc
C. Magnesium
D. Aluminum
94. Which of the following is not a common term relating to the
classification of fits?
A. Tunking
B. Snug
C. Medium force fit
D. Bound95. In usual spur gearing, which of the following statement(s) is correct?
A. Pitch circle and base circle are the same
B. Working depth includes the clearance
C. Tooth outline are usually involutes curves
D. Tooth outline are usually cycloidal curves
96. In general, the design stress and factor of safety are related as
follows:
A. Design Stress= ultimate stress times factor of safety
B. Design Stress= ultimate stress divided by factor of safety
C. Factor of Safety= design stress divided by ultimate stress
D. Ultimate Stress= factor of safety divided by design stress
97. In usual spur gearing, the:
A. Pitch circle and base circle are the same
B. Working depth includes the clearance
C. Tooth outline are usually cyclonical curves
D. Tooth outline are usually involutes curves
98. Which of the following is the not the other name of circumferential
stress for thin walled cylinders.
A. Hoop stress
B. Girth stress
C. Tangential stress
D. Longitudinal stress
99. How do you call the ratio of the volumetric stress to volumetric
strain?
A. Modulus in shear
B. Stress to strain ratio
C. Volumetric ratio
D. Bulk modulus
100. Hearing bone gears which:
A. Do not operate parallel shafts
B. Have a line contact between the teeth
C. Tend to produce and thrust on the shafts
D. Consist of two left handed helical gears
MODULE 5
1.The ability of metals to standloads without breaking down:
A.strain
B.stress
C.elasticity
D.strength
2. Which of the following is not a classification of iron ore?
A.Siderite
B.Hermatite
C.Sulfurite
D.Magnetite3. Ferrous metals contain a relatively large amount of:
A.manganese
B. carbon
C.sulfur
D. phosphorous
4. Which of the following metal is easy to chisel?
A. alloy steel
B. manganese steel
C. stainless steel
D. cast iron
5. The ability of material of metal to resist being a crushed is:
A. fatigue strength
B.bending strength
C.torsional Strength
D.Compressive strength
6.Which of the following is not part of the headstock?
A. anvil
B.spindle
C. motor
D.back pressure
7. Which of the following is not used to temper steel?
A. oil bath
B. brine/salt bath
C. steam bath
D. water bath
8. Which of the following is not a kind of cast iron?
A. gray iron
B. white iron
C. malleable iron
D. lead iron
9. A machinery operation whereby the tool rotates while the feed is
stationary.
A. shaping
B. milling
C. turning
D. reaming
10. What process does not belong to the group?
A. brazing
B. soldering
C. hardening
D. resistance welding
11. Which tool does not belong to the group?
A. vice grip
B. feeler gage
C. torque wrench
D. Adjustable wrench
12. Which of the following metals is non-magnetic?
A. manganese steel
B. cast steel
C. alloy steel
D. cast iron
13. One important skill that operators of machine tools must have is an
understanding of measurement which demands:
A. speed
B. precision
C. sociability
D. neatness
14. Which of the following is not part of a lathe machine?
A. fan
B. carriage
C. headstock
D. tailstock15. The machine which can flatten surface on a horizontal, vertical or angular
plane is:
A. drilling machine
B. shaper machine
C. power saw
D. lathe machine
16. Which of the following is not the work of a machinist?
A. reboring
B. overhauling
C. grinding
D. boring
17. The area of the machine shop whose metal is being melted to form a new
shape is the:
A.foundry area
B.tool and die
C.welding area
D.mass production area
18. A machine used in testing steel generally strikes the specimen with an
energy from 220 to 265 ft-lb.
A.izod test
B.Charpy test
C. Rockwell test
D. Test blocks
19. An iron in which most of the carbon is chemically combined with the iron:
A. cast iron
B. gray iron
C. white iron
D. malleable iron
20. Through how many degrees must an involute cam turn in order to raise
its follower 3 inches if the diameter of the base circle is 5 inches?
A. 58.7 degrees
B. 180 degrees
C. 64.4 degrees
D. 68.79 degrees
21.The space between the adjacent teeth:
A. tooth
B. flank
C. backlash
D. width
22. An iron has physical properties closely resembling those of mild steel:
A. malleable cast iron
B. malleable iron
C. white iron
D. gray iron
23.Gears use to transmit power between shafts axis of which it intersect:
A. spur gears
B. bevel gears
C. helical gears
D. straight bevel gears
24.An important accessories of milling machines:
A. milling machine vise
B.Cutters
C. ram
D.Vertical milling attachment
25.They are usually the steel or steel casting:
A. mild steel
B. carbon steel
C. fire box steel
D.Drop forge dies
26. The cheapest and the most abundant engineering material.A. aluminum
B. steel
C. cast iron
D. babbitts
27. Milling machine accessories are used to hold milling cutter in the milling
machine:
A. spindle nose tooling
B. Milling machine cise
C. Vertical milling attachment
D. milling machine arbors
28. The size of an equal-leg length fillet weid shall be based on the length of
the largest:
A. isosceles right triangle
B. squeare
C. right triangle
D. rectangle
29. If gears cannot connect parallel shafts, they are called:
A. cycloidal gears
B.helical gears
C.spur gears
D.toothed gears
30. The path traced by a point moving at a fixed distance front an axis and
with a uniform motion to the axis and a point moving such a path:
A. helical motion
B. spherical motion
C. translational
D. path of a point
31. The maximum stress which is reached during a tension test:
A. stress
B. elasticity
C. strain
D. tensile strength
32. The frustums of two cones are use in a manner to permit a variation of
velocity ratio between two parallel shafts:
A. evans friction cones
B. bevel cones
C. spherical cones
D. friction gearing
33. Weld metal impact specimen shall be taken across the weld with one
face substantially parallel to and within:
A.3/4”
B.1/32”
C.1/4”
D.1/16”
34. A joint between two overlapping members in which the overlapped edge
of one member is welded with a fillet weld:
A. a single welded lap joint
B. double welded lap joint
C. a single welded lap joint with backing
D. tack weld
35. Imparts of reciprocating motion to a single point cutting tool:
A. dividing head
B. slotting attachment
C. circular pitch
D. circular milling attachment
36. The follower reciprocates or oscillates in a plane perpendicular to the axis
of rotation of the cam.
A. radial cam
B. cylindrical cam
C. cam curves
D. tangential cam37. Strength of a material is that of a stress intensity determined by
considering the maximum test load to act over the original area of the test
specimens:
A. yield point
B. ultimate strength
C. breaking strength
D. elastic strength
38. The follower reciprocates or oscillates in a plane parallel to the axis of the
rotation.
A. cam curves
B. cylindrical cam
C. tangential cam
D. radial cam
39. A test for pipe used for coiling in sizes 2 inches:
A. flaring
B. crush
C. flange
D. bend
40. An alloy in tin,copper,antimony, or sometimes lead:
A. gold
B. Babbitt
C. aluminum
D. cast iron
41. A weld place in a groove between two abutting members:
A. full fillet weld
B. tack weld
C. butt weld
D. fillet weld
42. A weld of approximately triangular cross section that join two surfaces at
approximately right angles as in lap joint, tee-joint, corner joint:
A. single welded lap joint
B. fillet weld
C. tack weld
D. butt weld
43. A corrosion occurs within or adjacent to a crevice formed by contacts with
another piece of the same or another metal:
A. pitting
B. galvanic
C.erosion
D. crevice
44. Wheels are sometimes used for the transmission of high power when an
approximately constant velocity ration in desired:
A. bevel cones
B. friction gearing
C. spur friction wheels
D. evans friction wheels
45. Gearing in which motion or power that is transmitted depends upon the
friction between the surfaces in contact.
A. bevel gears
B. spur friction
C. evans friction cones
D. friction gearing
46. A bevel gears of the same size mounted on a shaft at 90 degrees:
A. crown gears
B. spur gears
C. angular gears
D. miter gears47. A fillet weld whose size in equal to the thickness of the thinner joint
member:
A. butt joint
B. butt weld
C. tack weld
D. full fillet weld
48. The ration of stress to the corresponding strain below the proportional
limit:
A. stress strain diagram
B. gage method
C. modulus of elasticity
D. tensile strength
49. The searing strain of a block of metal 3 inches high is subject to a
shearing high force which distorts the top surface through a distance of
0.0036”.
A.0.0015 rad
B.0.008 rad
C.0.0010 rad
D.0.0012 rad
50. Determine the number of teeth in a driver of two spur gears mesh which
has a velocity ratio of 0.75 the driven gear has 36 teeth:
A. 50
B.46
C. 26
D. 48
51. Within the elastic limit the stress is proportional to strain.
A. Hooke’s law
B. modulus of elasticity
C. offset ratio
D. Buckingham’s principle
52. The corrosion of iron or iron-base-alloys:
A.rusting
B.crazing
C.chalking
D. fritting
53. Steel containing large amounts of mild nickel and chromium:
A. carbon steel
B. stainless steel
C.alloy steel
D. cat steel
54. It refers to any layer or deposit of extraneous material on the heattransfer-surface:
A. low line
B. pressure drop
C. fouling
D scaling
55. The total amount of permanent extension of the gage length measured
after the specimen has fractured and is expressed as percentage increase of
the original gage length:
A. elongation
B. strain
C. stress
D. elastic limit
56. It is used to enable milling machine to take climb milling cuts:
A. helical driving mechanism
B.Spindle
C.read out
D.backlash eliminator
57. A weld made to hold the parts of a weldment in proper alignment until the
final welds are made:A butt weld
B. tack weld
C. fillet weld
D. full fillet weld
58. The change in length per unit original length is:
A. strain
B. stress
C. deformation
D. elastic modulus
59. The temperature above which the alloy is liquid and will run:
A. melting point
B. fow point
C. pour point
D. liquids
60. A cone formed by elements which are perpendicular to the elements of
the pitch cone at the large end:
A. cone distance
B. back cone
C. root cone
D. cone center
61. A machine used for the testing of very thin steel or surface layers:
A. charpy test
B.Izod test
C. description test
D. rockwell test
62.A gear is on in which angle is 90 degrees that is the pitch no has become
a plane.
A. crown gear
B. angular gear
C. miter gear
D.spiral gear
63.The deterioration of organic coating characterized as completely:
A. chalking
B. rusting
C. chocking
D. fritting
64.Is a form of correction that develop on a highly localized areas on a metal
surfaces:
A. crevice
B. erosion
C. galvanic
D. spitting
65.Test is designed primarily for application to electric welded tubing for
detection of lack of penetration or overlaps resulting from flash removal in the
weld.
A. butt weld
B. paster
C. lap weld
D. double butt weld
66.Have the same thermal and minimum film thickness limitation as sleeve
bearing.
A. ball bearing
B. roller bearing
C. thrust bearing
D. oil bearing
67.An oil storage roof formed to approximately the surface of a right cone
supported only at its periphery:B. self-supporting dome roof
C. supported cone roof
D. self-supporting cone roof
68.Test sometimes referred to as an upsetting test:
A. bend
B.Flaring
C.flange
D.crush
69.What load P which cause a total deformation of 0.036 “ of a steel rock
which has a cross section area of 4 in and a length of 6 ft.
A.55, 000lb.
B. 40,000 lb.
C.60, 000lb.
D.50, 000lb.
70. An oil storage tank roof formed to approximately a spherical surface,
supported only at its periphery:
A. self-supporting umbrella roof
B. self-supporting cone roof
C. self-supporting
D. supported cone roof
71. The unit of deformation is called:
A. torsion
B. strain
C. stress
D. shear
72.A circle bounding the bottom of the teeth:
A. addendum circle
B. addendum cylinder
C. pitch circle
D. dedendum circle
73.A 3 “ diameter short shaft carrying 2 pulleys close to the bearings transmit
how much horsepower if the shafts makes 280 rpm.
A. 199 Hp
B. 198 HP
C. 200 Hp
D. 210 Hp
74.A cylindrical tank with 10 in. inside diameter contains oxygen gas at 2500
psi, calculate the required wall thickness in (mm) under stress of 28,00 psi.
A. 11.44 mm
B. 11.34 mm
C.10.6 mm
D.10.3 mm
75.The minimum clearance allowed for meshing spur gears with a circular
pitch of 0.1571 and diametral pitch of 20 the spur gear have 25 teeth.
A. 0.007855
B.0.007558
C.0.008578
D.0.007585
76.SAE steel that responds to heat treatment:
A. SAE 1060
B. SAE 1117
C. SAE 1030
D. SAE 1020
77. Which of the following is the differential of the shear equation?
A. bending moment
B. Load of the beam
C.tensile strength of the beam
D. slope of the beam78. Which of the following materials to be utilized to reduce cost the
manufacturing of large worm gears?
A. alloyed aluminum
B. bronze rim with cast iron spider
C. cast iron rim with bronze spider
D. all of these
79. It is hardening treatment whereby a cast metal is being heated to a very
high temperature then suddenly subjected to rapid cooling to improve
hardenability or wear resistance is called:
A. normalizing
B. tempering
C.annealing
D.quenching
80. Determine the estimated weight of an A-36 steel plates size 3/16 x6’x20’.
A.919 lbs.
B. 1012 lbs.
C.829 lbs.
D. 735 lbs.
81.The length of arc between the two sides of a gear tooth on the pitch circle:
A. circular thickness
B. axial plane
C. helix angle
D. chordal curves
82.Split pully or pulley made of separate section bolted together at the rim;
the maximum speed should be limited to about _____% of the maximum
speed of solid pulley.
A. 65 to 75%
B. 45 to 50%
C.55 to 60%
D.80 to 90%
83.Killed steel is very much associated with:
A. manganese
B. Sulphur
C. phosphorous
D.silicon
84.Determine the estimated weight of an A-36 steel plate of size 1/2x4x8.
A. 289 kg
B.332 kg
C. 301 kg
D. 297 kg
85.A type of welding whereby a wire or powder from the nozzle of a spray
gun is fused by a gas flame, arc or plasma jet and the molten particles are
projected in a form of a spray by means of compressed air or gas.
A. electro slug building
B. electro beam welding
C.plasma arc welding
D.metal spray welding
86.Heating of metal above the critical temperature and then cooling slowly
usually in the furnace to reduce the hardness and improve the machinability
is called:
A. normalizing
B. annealing
C. tempering
D. quenching
87. Accident prevention is:
A. an association of employers, organization& individuals
B. the foreman’s responsibility just as much as production
C. the responsibility of top management
D.a job of a safety director88.Major component of bronze casting:
A. copper
B. manganese
C.zinc
D. lead
89.Commonly utilized/cheapest shaft material available in the market with
carbon content of 0.28 to 0.34%.
A. SAE 4132
B. SAE 4320
C. SAE 1030
D. SAE 4130
90. Alloy steel known for its resistance to corrosion abrasing and wear that is
usually ideal for mill grinding of ore in cement and concentrator application it
is usually combined with molybdenum to increase the depth hardening.
A. manganese chromium steel
B. chromium-moly steel
C. chorome-nickel-moly-steel
D. manganese-moly steel
91. Split pully or pulley made of separate section bolted together at the rim
the maximum speed should be limited to about ___% of the maximum speed
of solid pulley.
A.65 to 75%
B.45 to 50 %
C. 55 to 60%
D. 80 to90%
92.Major component of bronze casting is:
A. copper
B. manganese
C. zinc
D. lead
93.Galvanized steel plate is:
A.aluminum
B. tin
C.zinc
D.manganese
94. What heat treatment process can cast steel materials of high chrome
high manganese, etc. type steel be subjected for the purpose of machining
process ?
A.annealing
B.tempering
C.normalizing
D.quenching
95. Cast alloy steel for very high temperature application:
A.manganese-nickel steel casting
B. high chrome steel casting
C.chrome nickel steel casting
D.high manganese casting
96. Flexible material used to seal pressurized fluids, normally under dynamic
condition:
A. nylon
B. seal
C. teflon
D. packing
97. A type of gear tooth cut inside a cylinder or ring:
A. rack gear
B. ring gear
C. miter gear
D. internal gear
98. It has molybdenum ally except:
A. SAE 43xx
B. SAE 41xx
C. SAE 6xxxD. SAE 5xxx
99.To prevent leakage in dynamic seal:
A. gasket
B. seals
C.felts
D. packings
100. Which of the following elements when large quantity is harmful to the
ferrous metal?
A. sulfur
B. silicon
C. zinc
D. aluminum
[Show More]