OK State Licensing - Locksmith

OK State Licensing - Locksmith What joins a mortise cylinder to a mortise lock? - ANS - Threads on the cylinder and a set screw The key shown above matches the locks manufactured by: - ANS - Schlage What type of key n ...

OK State Licensing - Locksmith What joins a mortise cylinder to a mortise lock? - ANS - Threads on the cylinder and a set screw The key shown above matches the locks manufactured by: - ANS - Schlage What type of key normally must be duplicated with an end mill cutter? - ANS - Paracentric What is needed to remove the outside knob of a Schlage entrance set? - ANS - Key and pin punch A licensee who moves or changes employers shall notify the Oklahoma Department of Labor within how many days? - ANS - 14 A technician is weak; having chills and cannot seem to get enough to drink. What is the likely cause of the technician's symptoms? - ANS - High blood sugar The Oklahoma Alarm and Locksmith Industry Act applies to: - ANS - Persons who sell, install and service alarm systems What type of tumbler is most commonly used in a file cabinet lock? - ANS - Short wafer What is the maximum amount of administrative fines that can be levied against any person for violations of the Oklahoma Alarm and Locksmith Industry Act? - ANS - $1,000 A coordinator is required on a pair of fire doors having: - ANS - An overlapping astragal With proper care, which cutter material typically provides the longest use? - ANS - Carbide Thru-bolt trim is used on many mortise locks to: - ANS - Make the installation look better If a conflict exists between adopted references, the reference that applies shall be the one: - ANS - With the more stringent standard What brand of lock does a WR3 or 1054WB key blank fit? - ANS - Weiser A classroom function lock is designed so that: - ANS - A key is required to lock the room The key shown above matches locks manufactured by: - ANS - Dexter Pick guns work by: - ANS - Bouncing the top pins above the shear line What brand of lock does a M1 or 1092 key blank fit? - ANS - Master What brand of lock does a WK2 or 1175 key blank fit? - ANS - Weslock A hotel function lockset is one that: - ANS - Requires a key or card from the outside in order to enter Which tools are used to manipulate a lock? - ANS - Tension wrench and hook pick When removing a kwikset entrance set, what should the locksmith remove first? - ANS - Screws on the inside of the knob Difficulty inserting or removing the key blank during imprisoning is caused by: - ANS - Improper lubricating the lock Of the following materials, which key blank produces the most obvious marks? - ANS - Brass A power tool has a 3-pronged plug but the only available outlets are 2-pronged. What should the technician do? - ANS - Locate a 3-pronged outlet How many trainees per job site can work under the supervision of a licensed technician? - ANS - Three What length of graduation is found in a standard universal pin kit with 0.115 diameter pins? - ANS - 0.003 When key changing a Standard Group 2 combination, the technician should dial the old combination on the change mark and: - ANS - Insert the key change from the back of the wheel pack A passage set is a lockset that - ANS - Is not lockable What is the primary hazard when workin with gas-powered tools in an indoor space? - ANS - Hazardous vapors or fumes When using a portable ladder to access an upper landing surface, how many feet above the landing's surface must the side rails of the ladder extend? - ANS - Three A licensed technician or salesperson shall only work under the supervision of: - ANS - A licensed manager What function describes a lockset that permits emergency access when locked, but allows free egress? - ANS - Privacy Which pick is designed to pick one pin at a time? - ANS - Hook Which of the following brands of locks is considered "high security"? - ANS - Medeco How many tumblers and springs are in a standard 5-cut key cylinder? - ANS - 5 In lock picking, the tension wrench: - ANS - Holds the tumblers at the shear line A rim cylinder is held in place by: - ANS - Two screws from the back of the cylinder What is the shape of a top pin? - ANS - Flat on both ends Handing of doors for lockset installation is referenced from the: - ANS - Egress side According to NFPA 80, a 'self-closing door' is one that: - ANS - Is normally open but will close by some activation device in case of fire The purpose of a tailpiece is to: - ANS - Transfer the motion of the plug to the lock What is the total fee required to renew a technician or sales license that is not received or postmarked by June 30th? - ANS - $70 What brand of lock does a K1 or L1054B key blank fit? - ANS - Master A technician working in a hot attic feels nauseous, dizzy, and fatigued. His skin is hot, dry and flushed, but he is not perspiring. What is the likely cause of the technician's symptoms? - ANS - Heat stroke While in engaged in alarm and locksmith work, the company's license number must be at least 2" in size and displayed: - ANS - On all sides of all vehicles where the company name is displayed In order to be eligible for a technician or salesperson license, an individual must be at least how many years of age? - ANS - 18 What crime is committed by a technician or salesperson that falsifies a customer's signature or adds content to a document that has already been signed? - ANS - Fraud A pippin duke is primarily used to: - ANS - Hand file a key The location in a pin cylinder where the tumbler surfaces align without obstruction to allow rotation is the: - ANS - Shear line What does the number on the face of a file cabinet lock represent? - ANS - Replacement key code In residential construction, workers must be protected by a harness if they can fall more than how many feet? - ANS - 6 The distance from the key blank shoulder to the center of the first cut indicates: - ANS - Cut spacing Which material offers the greatest key durability? - ANS - Nickel silver A permit-required confined space is one that contains, or could contain: - ANS - A recognized or serious hazard If a conflict exists between the adopted reference, and a chapter in the Alarm and Locksmith Industry Rules, which statement is true? - ANS - The requirements of this chapter shall be followed When leaning a ladder against a wall, how far from the wall should the foot of the ladder be located? - ANS - 1/4 the working length of the ladder What safety features must be on power tools used in the work place? - ANS - Properly fitting guards and appropriate safety switches What must be worn while working on a ladder? - ANS - Slip resistant footwear To create a safe handhold to reach another level, how many feet above the landing point should the ladder be extended? - ANS - Three The slot in a standard group 2 driver disk of a safe wheel pack is called the: - ANS - Fence What are the proper tools to use to disassemble a cylinder when a key is not available? - ANS - Vise grips and tweezers What is the standard residential backseat? - ANS - 2 3/8" What is the application and license fee for a technician or salesperson? - ANS - $49 A plug follower is used to: - ANS - Retain the springs and top pins when disassembling a cylinder A technician feel off a ladder and injured his wrist. In order to be covered by worker's compensation, the injury must be reported to his employer within: - ANS - 30 days A technician experiences sudden weakness on the right side of her body and is having trouble speaking and understanding simple statements. What is the likely cause of her symptoms? - ANS - Stroke What term applies to a key that is furnished by the lock manufacturer? - ANS - Original When a installing a mortise cylinder in a door, in what direction should the keyway face? - ANS - 12 o'clock What is a common mortise cylinder malfunction? - ANS - Loose or missing cam screws What is the shape of a bottom pin? - ANS - Pointed on one end, flat on the other end When providing first aid to a victim of heat stroke, what should be done first? - ANS - Take steps to lower the person's body temperature When hand changing a safe combination, the locksmith should: - ANS - Use the Sargent and Greenleaf changing procedure Panic bars are typically found: - ANS - On fire exits on public buildings The key shown above matches locks manufactured by: - ANS - Weslock When performing alarm and locksmith work in Oklahoma, a licensee must possess an Oklahoma license in the appropriate industry area and a: - ANS - Valid, state-issued photo identification What size hole is required for a cabinet utility lock? - ANS - 3/4" Personal protective equipment should be used protect employees from workplace hazard when: - ANS - Hazards cannot be eliminated with an engineering or workplace controls What size hole is required for most doorknob sets? - ANS - 2 1/8" Which clue indicates an electrical hazard? - ANS - Warm tools or cords When making up a new combination number, the numbers in the combination should be how many numbers apart? - ANS - At least 12 A technician is allowed to perform work within: - ANS - The alarm industry area(s) for which he is licensed Upon conviction, any individual violating any provision of the Oklahoma Alarm and Locksmith Industry Act shall be guilty of a misdemeanor punishable by up to one year confinement in the county jail and/or maximum fine of: - ANS - $500 What is the recommended emergency treatment for a person experiencing low blood sugar? - ANS - Eat a high sugar food, such as hard candy or fruit juice The key turns in a plunger-type lock mounted in the second drawer of an insulated file cabinet, but the lock will not pop out. What is the best way to open the drawer? - ANS - Shim the plug from the front of the lock