Report for Experiment #16
Electric Field and Electric Potential
Ali Hussein
Lab Partner: Cory Lafleur
TA: Hamza Ahmed
Monday, September 30, 2019
Abstract
There exists equipotential lines, which are lines found bet
...
Report for Experiment #16
Electric Field and Electric Potential
Ali Hussein
Lab Partner: Cory Lafleur
TA: Hamza Ahmed
Monday, September 30, 2019
Abstract
There exists equipotential lines, which are lines found between a negative and a positive
electrode, and the potential difference V remains constant throughout. And finding these lines,
which form from oppositely-charged parallel electrodes and concentric electrodes, allow for the
electric field to be calculated. It’s from this information, that the electric field between the two
electrodes was found to be constant at 92.746 ± 3.256 V/m. This is a 7.254% error from the
theoretical value, 100.000 V/m. And in concentric electrodes, the potential difference had showna logarithmic trend line in relation to distance from the center cylindrical electrode, that implied
that the electric field was inversely proportional to the distance. So by comparing the measured
electric field to the theoretical electric field, the average potential difference between the two
equipotential lines was found to be -4.080 ± 0.001 V, which is a 12.670% error from the
theoretical value -4.672 V.
Introduction:
The purpose of the lab was to comprehend the relation between electric potential and
electric field by testing the electric potential and electric field interactions between two
electrodes. Electric fields are regions around a charged object in which forces would repel
similar and attract opposite charges. Electric potential describes the work per unit of charge;
potential charges are represented in volts (V). Potential between objects can be mapped out using
equipotential lines (as observed in Formula 1.1) where displays the difference of potentials over
the difference in distance.
The objective of the experiment was to investigate the characteristics of the electric
potential and electric fields for 2-dimensional charge configurations in two scenarios. The first
being in the first investigation which simulates the electric field and potential distributions on
parallel plate capacitor. This investigation has the user place two brass electrodes on conducting
paper (with power supply and voltmeter) so they can then use a probe tipped wire to mark lines
at specific volt charges (1V, 2V, 3V, etc.). The scenario in the second investigation simulated
fields between charges on infinitely long cylinders with respect to both the electric field and
potential. In this investigation, a cylindrical brass electrode surrounded by a circular electrode
(with power supply and voltmeter) are set up and the user is tasked with identifying circles at
specific volt charges (equipotential lines) using a probe tipped wire.
Starting with the first investigation, the relationship between the equipotential lines and
measured distances from the electrode solved for the electric field (as seen in Formula 1.1; also
represented by Formula 1.2 indicating electric field as a magnitude). Then the user is asked to
calculate the average position using Formula 1.3, and the relation between the electric field and
average position gives the electric potential represented by Formula 1.4. The error of electrical
field is found using Formula 1.5
The initial measurements for investigation 2 are the same as investigation 1 (indicate volt
charge at equipotential lines and their distances from electrode; this time it is the central
electrode), but since the equipotential lines are circles, the distance from the electrode is found
along each coordinate axes and averaged together (using Formula 2.1). The error for the average
radius for the equipotential line is found using the standard deviation (Formula 2.2). And to solve
for the theoretical potential at the equipotential line, as seen in Formula 2.3, the initial potential
at the central cylinder (V0 = 10V) is multiplied by, the logarithmic difference between the radius
of the circle electrode and the radius of the respective equipotential line over the difference of the
radius of the circle electrode and the cylindrical electrode. The electrical field was found using
Formula 1.1; taking the measured distance from the average radius. To solve for the theoreticalelectric field, first the user finds its location which is halfway between equipotential lines, found
using Formula 1.3; its error found using Formula 1.5. And the electric field is found using
Formula 2.4, taking the initial voltage over the logarithmic difference of the circle electrode
radius and the cylindrical electrode radius, all multiplied by the reciprocal of the average radius.
E❑
x=
−ΔV
Δ x
=
−V ❑
b−V ❑a
x❑b−x❑a (Formula 1.1)
E=constant (Formula 1.2)
x❑
avg=
x❑
a+x❑b
2
(Formula 1.3)
V (x)=Ex (Formula 1.4)
√❑
δ z=¿ (Formula 1.5)
r❑
avg=
(r❑1+r ❑2+r❑3+...r❑n)
n
(Formula 2.1)
σ=√❑ (Formula 2.2)
[Show More]