CENSECFOR Operator Training - M11 Service Pistol

CENSECFOR Operator Training - M11 Service Pistol Which of the following safety notations states: "Operating or maintenance procedures, practice, or condition that if not strictly observed WILL result in death or serio ...

CENSECFOR Operator Training - M11 Service Pistol Which of the following safety notations states: "Operating or maintenance procedures, practice, or condition that if not strictly observed WILL result in death or serious injury, or threaten the primary mission of the ship"? - ANS - Danger A _____ safety notation deals with an operation, procedure, practice, or condition that could result in injury or death if not carefully observed or followed. - ANS - Warning Proper weapon handling is the responsibility of the person in control of the weapon. Pointing or aiming a functional weapon at any person is _______ except when required in the performance of duty/ - ANS - Unlawful What weapon caliber is the M11 service pistol? - ANS - 9mm What is the standard service life of the M11 service pistol? - ANS - 15,000 rds Which has the greater trigger pull? - ANS - Double-action A safety/function check should be performed ______. - ANS - Anytime the weapon is reassembled What is the second step performed as part of the M11 service pistol safety/function check procedures. - ANS - Retract the slide and release it. The magazine follower should push up on the slide stop, locking the slide to the rear Which of the following is NOT one of the four weapons safety rules? - ANS - Keep your weapon without a round in the chamber until you intend to fire. What is the minimum trigger pull of the M11 service pistol in single-action mode? - ANS - 4.4 lbs Which condition is associated with an unintentional interruption in the cycle of operation? - ANS - Stoppage What is the most prevalent factor in most accidents involving firearms? - ANS - Assuming the weapon is not loaded. How many rounds maximum does the M11 service pistol magazine hold? - ANS - 13 rds Which type of stoppage is displayed in the picture below? (slide out of battery, one round in chamber and one round directly behind) - ANS - Double feed Which of the following is one of the four weapons safety rules? - ANS - Keep the weapon on safe until you intend to fire. What is the maximum effective range (in meters) of the M11 service pistol? - ANS - 46 m Which action listed below is the first step when performing a remedial action in tactical situations? - ANS - Seek cover (if available) Which of the Weapons Condition Codes is not applicable for the M11 service pistol? - ANS - 2 Identify the component show in the picture. (Shows magazine) - ANS - Magazine Assembly Which of the following is NOT a description of a Condition Code for the M11 service pistol? - ANS - Magazine inserted, round in chamber, slide forward, hammer back. Magazine inserted, chamber empty, slide forward, and hammer forward is which M11 service pistol weapon Condition Code? - ANS - 3 In which weapon carry method are the arms extended and the pistol raised to just below eye level so a clear field of view is maintained? - ANS - Ready Carry What is the status of the M11 service pistol in Condition 1? - ANS - Magazine inserted, round in chamber, slide forward, and hammer forward. Identify the component show in the picture below? (Shows ruler, spring, and guide) - ANS - Recoil Spring Guide Identify the position demonstrated in the picture below. (Shows male from profile, holding pistol muzzle up) - ANS - Administrative Transport What actions will be taken when given a LOAD command? - ANS - Take the weapon from Condition 4 to Condition 3 Which component holds the firing pin and extractor? - ANS - Slide and Barrel Assembly During which phase of the drawing process is the eye's focus first set on the center of mass on target? - ANS - Grab What standard weapon handling command would be given to take the weapon from Condition 1 to Condition 4? - ANS - Unload During this step the hammer strikes the firing pin, which, in turn, strikes the cartridge primer. - ANS - Firing Which of the following is NOT a standard weapon handling command? - ANS - Hold Fire Which step in the cycle of operation does the below graphic represent? (slide moving forward with round) - ANS - Feeding Which pistol carry method is used when enemy contact is probable? - ANS - Alert Carry Identify the following cycle of operation step: With the rearward motion of slide, the extractor pulls a cartridge from the chamber. - ANS - Extracting During which step is the cartridge pulled from the chamber? - ANS - Extracting The drawing techniques for the M11 service pistol are: - ANS - Grab, Draw, Smack, Look and Squeeze Which weapon handling command is associated with the action of engaging the threat? - ANS - Fire Which M11 service pistol operational term describes rearward movement of the slide overriding the hammer and forcing the hammer into its most rearward position? - ANS - Cocking Which of the following stances provides better recoil management and quicker target acquisition? - ANS - Isosceles The _____ should push up on the slide stop, locking the slide to the rear. - ANS - Magazine Follower A _____ often results in an audible pop and/or reduced recoil. - ANS - Hangfire Which of the following can be caused by dirty ammunition? - ANS - Slide not forward in battery _____ provides optimal safety with the hammer in either the cocked or decocked position. - ANS - The automatic firing pin lock Which of the following is NOT a typical shooter-induced stoppage for the M11 service pistol? - ANS - Engaging the slide stop while firing Approximately how many pounds of pressure is required to cock and release the hammer in the Double-Action mode of operation? - ANS - 12 lbs Upon completion of fieldstripping the M11 service pistol, how many separate components will there be total? - ANS - 5 Which component houses the cartridge for firing? - ANS - Barrel During this step the hammer strikes the firing pin, which in turn strikes the cartridge primer. - ANS - Firing