Data Communications and Networking

Document Content and Description Below

Data Communications and Networking Lab exercise no. 1.3: Configuring VLANs Topology Addressing Table Device Interface IP Address Subnet Mask VLAN PC1 NIC 172.17.10.21 255.255.255.0 10 PC2 NIC 17... 2.17.20.22 255.255.255.0 20 PC3 NIC 172.17.30.23 255.255.255.0 30 PC4 NIC 172.17.10.24 255.255.255.0 10 PC5 NIC 172.17.20.25 255.255.255.0 20 PC6 NIC 172.17.30.26 255.255.255.0 30 Objectives Part 1: Verify the Default VLAN Configuration Part 2: Configure VLANs Part 3: Assign VLANs to Ports Background VLANs are helpful in the administration of logical groups, allowing members of a group to be easily moved, changed, or added. This activity focuses on creating and naming VLANs, and assigning access ports to specific VLANs. Edited by: Dr. Essam Alnatsheh Page 1 of 5 This study source was downloaded by 100000840858457 from CourseHero.com on 07-05-2022 15:57:36 GMT -05:00 https://www.coursehero.com/file/51191449/13-Packet-Tracer-Configuring-VLANs-Instructionsdocx/Packet Tracer – Configuring VLANs Part 1: View the Default VLAN Configuration Step 1: Display the current VLANs. On S1, issue the command that displays all VLANs configured. By default, all interfaces are assigned to VLAN 1. Step 2: Verify connectivity between PCs on the same network. Notice that each PC can ping the other PC that shares the same network.  PC1 can ping PC4  PC2 can ping PC5  PC3 can ping PC6 Pings to PCs in other networks fail. What benefit will configuring VLANs provide to the current configuration? The vlan can connecting each other without using router . Part 2: Configure VLANs Step 1: Create and name VLANs on S1. Create the following VLANs. Names are case-sensitive:  VLAN 10: Faculty/Staff  VLAN 20: Students  VLAN 30: Guest(Default)  VLAN 99: Management&Native  VLAN 150: VOICE Which commands do you used to accomplish this step? S1>enable S1#config t Enter configuration commands, one per line. End with CNTL/Z. S1(config)#vlan 10 S1(config-vlan)#name Faculty/staff S1(config-vlan)#end S1#config t S1(config)#vlan 20 S1(config-vlan)#name student S1(config-vlan)#end S1#config t Enter configuration commands, one per line. End with CNTL/Z. S1(config)#vlan 30 S1(config-vlan)#name guest S1(config-vlan)#end Edited by: Dr. Essam Alnatsheh Page 2 of 5 This study source was downloaded by 100000840858457 from CourseHero.com on 07-05-2022 15:57:36 GMT -05:00 https://www.coursehero.com/file/51191449/13-Packet-Tracer-Configuring-VLANs-Instructionsdocx/Packet Tracer – Configuring VLANs S1#config t Enter configuration commands, one per line. End with CNTL/Z. S1(config)#vlan 99 S1(config-vlan)#name manegment S1(config-vlan)#end S1#config t Enter configuration commands, one per line. End with CNTL/Z. S1(config)#vlan 150 S1(config-vlan)#name voice S1(config-vlan)#end Step 2: S1(config-vlan)#end Verify the VLAN configuration. Which command will only display in brief the VLAN name, status, and associated ports on a switch? S1#show vlan brief Step 3: Create the VLANs on S2 and S3. Using the same commands from Step 1, create and name the same VLANs on S2 and S3. Step 4: Verify the VLAN configuration. Part 3: Assign VLANs to Ports Step 1: Assign VLANs to the active ports on S2. Configure the interfaces as access ports and assign the VLANs as follows:  VLAN 10: FastEthernet 0/11  VLAN 20: FastEthernet 0/18  VLAN 30: FastEthernet 0/6 S2(config)# interface f0/11 S2(config-if)# switchport mode access S2(config-if)# switchport access vlan 10 S2(config-if)# interface f0/18 S2(config-if)# switchport mode access S2(config-if)# switchport access vlan 20 S2(config-if)# interface f0/6 S2(config-if)# switchport mode access S2(config-if)# switchport access vlan 30 Step 2: Assign VLANs to the active ports on S3. S3 uses the same VLAN access port assignments as S2. Configure the interfaces as access ports and assign the VLANs as follows:  VLAN 10: FastEthernet 0/11  VLAN 20: FastEthernet 0/18  VLAN 30: FastEthernet 0/6 Edited by: Dr. Essam Alnatsheh Page 3 of 5 This study source was downloaded by 100000840858457 from CourseHero.com on 07-05-2022 15:57:36 GMT -05:00 https://www.coursehero.com/file/51191449/13-Packet-Tracer-Configuring-VLANs-Instructionsdocx/Packet Tracer – Configuring VLANs S3(config)# interface f0/11 S3(config-if)# switchport mode access S3(config-if)# switchport access vlan 10 S3(config-if)# interface f0/18 S3(config-if)# switchport mode access S3(config-if)# switchport access vlan 20 S3(config-if)# interface f0/6 S3(config-if)# switchport mode access S3(config-if)# switchport access vlan 30 Step 3: Assign the VOICE VLAN to FastEthernet 0/11 on S3. As shown in the topology, the S3 FastEthernet 0/11 interface connects to a Cisco IP Phone and PC4. The IP phone contains an integrated three-port 10/100 switch. One port on the phone is labeled Switch and connects to F0/4. Another port on the phone is labeled PC and connects to PC4. The IP phone also has an internal port that connects to the IP phone functions. The S3 F0/11 interface must be configured to support user traffic to PC4 using VLAN 10 and voice traffic to the IP phone using VLAN 150. S3(config)# interface f0/11 S3(config-if)# mls qos trust cos S3(config-if)# switchport voice vlan 150 S3(config-if)# end [Show More]

Last updated: 2 years ago

Preview 1 out of 5 pages