NACE CIP1: Standards Questions and Answers 100% Verified

Document Content and Description Below

NACE CIP1: Standards Questions and Answers 100% Verified NACE No. 1/SSPC-SP 5 ✔✔White Metal Blast Cleaning; free from all visible mill scale, rust, and coatings with 0% staining NACE No. 2/SSPC-SP 10 ✔✔Near White Metal Blast Cleaning; free from all visible mill scale, rust, coatings with 5% staining allowed NACE No. 3/SSPC-SP 6 ✔✔Commercial Blast Cleaning; free from all visible mill scale, rust, coatings with 33% staining allowed NACE No. 8/SSPC-SP 14 ✔✔Industrial Blast Cleaning; allows tightly adherent mill scale, rust, and coatings on 10% of each unit area NACE No. 4/SSPC-SP 7 ✔✔Brush Off Blast Cleaning; all tightly adherent mill scale, rust, and coatings can remain but all loosely adherent must be removed Sa 3 ✔✔Blast Cleaning to Visually Clean Steel Sa 2 1/2 ✔✔Very Thorough Blast Cleaning Sa 2 ✔✔Thorough Blast Cleaning Sa 1 ✔✔Light Blast Cleaning St 2 ✔✔Thorough Hand and Power Tool Cleaning St 3 ✔✔Very Thorough Hand and Power Tool Cleaning SSPC-SP 2 ✔✔Hand Tool Cleaning; removes all loose mill scale, rust, and coatings SSPC-SP 3 ✔✔Power Tool Cleaning; removes all loose mill scale, rust, and coatings SSPC-SP 15 ✔✔Commercial Grade Power Tool Cleaning; removes all tightly adherent mill scale, rust, and coatings but allows staining on up to 33% of unit area w/ minimum 1 mil surface profile SSPC-SP 11 ✔✔Power Tool Cleaning to Bare Metal; removes all tightly adherent mill scale, rust, and coatings w/ minimum 1 mil surface profile SSPC-SP 16 ✔✔Brush-Off Blast Cleaning of Coated and Uncoated Galvanized Steel, Stainless Steels, and Non-Ferrous Metals NACE SP0178 ✔✔Addresses design, fabrication, and surface finishing (i.e. smoothing welds/rounding edges) SSPC-SP 1 ✔✔Solvent Cleaning; the only commonly used standard that formally governs solvent cleaning SSPC-VIS 3 ✔✔SP visual guides and standards for power tool cleaning; initial rust grade before surface prep ASTM D 4285 ✔✔Test Method for Indicating Oil or Water in Compressed Air "Blotter Test" SSPC-VIS 1 ✔✔Guide and Reference Photographs for Steel Surfaces Prepared by Dry Abrasive Blast Cleaning ISO 8501-1 ✔✔Visual guide to rust grades before surface preparation WJ-1 ✔✔Waterjetting Clean to Bare Substrate; allows 0% tightly adhered mill scale, rust, and coatings WJ-2 ✔✔Waterjetting allowing 5% tightly adhered mill scale, rust, and coatings WJ-3 ✔✔Waterjetting allowing 33% tightly adhered mill scale, rust, and coatings WJ-4 ✔✔Waterjetting allowing tightly adhered mill scale, rust, and coatings ISO 8502-3 ✔✔Detecting dust on the substrate by pressing a clear tape to the surface, removing it, and noting the amount of dust ASTM C 136 ✔✔Sieve Test; enables the inspector to measure the particle size and distribution of the abrasive ASTM D 4417 ✔✔Standard test methods for field measurement of surface profile of Blast cleaned steel; Method A: Iso Comparator; Method B: Electronic Gauge; Method C: Profile Tape NACE SP0287 ✔✔Standard practice for field measurement of surface profile of abrasive blastcleaned steel surfaces using a replica tape SSPC Technology Guide No. 12 ✔✔Illumination of Industrial Painting Projects; For Applicators: Min.-20 foot candles of light and Recommended-50 foot candles For Inspectors: Min-50 foot candles and Recommended-200 foot candles SSPC ACS-1/ANSI/NACE No. 13 ✔✔Industrial coating and lining specialist qualification and certification; joint training standard for coating applicators SSPC PA 2 ✔✔DFT Measurement with Magnetic Gauges; Type 1: Banana Gauge Type 2: Electronic Gauge NACE SP0188 ✔✔High and Low Voltage Holiday Testing

[Show More]

Last updated: 3 years ago

Preview 1 out of 6 pages

Buy Now

Instant download