MSSC - Manufacturing Processes and
Production Questions and Answers
100% Pass
The three common types of mechanisms are levers, ______, and inclined planes. ✔✔wheels
The metric system expresses force in ______. ✔✔newt
...
MSSC - Manufacturing Processes and
Production Questions and Answers
100% Pass
The three common types of mechanisms are levers, ______, and inclined planes. ✔✔wheels
The metric system expresses force in ______. ✔✔newtons
A spring scale is used to measure ______. ✔✔force
The English unit of measure of weight is the ______. ✔✔pound-force (lb-f)
The Law of Moments can be used to determine ______. ✔✔both the force needed to balance OR
force needed to move a load
Torque can be calculated by multiplying the distance from the fulcrum and ______. ✔✔the force
applied
A force that makes an object rotate about a point is called ______. ✔✔torque
A second-class lever has its ______. ✔✔load between the fulcrum and the effort arm
A third-class lever has its ______. ✔✔effort arm between the fulcrum and the load
A(n) ______ is produced when forces applied to a lever cause it to rotate. ✔✔rotational moment
Mechanical advantage is the ratio of the force required to move a load divided by _____. ✔✔the
effort force applied
The mechanical advantage of a third-class lever can be found by the ratio of the length of the
______ arm divided by the length of the ______ arm. ✔✔effort, resistance
The coefficient of friction is the ratio of the force of friction divided by the ______. ✔✔normal
force
Rolling friction is ______. ✔✔less than both static and kinetic friction
What is the unit of measure for the coefficient of friction? ✔✔it has no unit
One application that takes advantage if both high and low friction is a(n) ______. ✔✔belt sander
A wheel reduces friction because _____ friction is less than sliding friction. ✔✔rolling
The mechanical advantage of an inclined plane is the ratio of the ______ of the inclined plane
divided by its ______. ✔✔length, height
The double rocker linkage is one type of ______ linkage. ✔✔four bar
The slider crank linkage is also known as the ______ linkage. ✔✔three bar
What type of linkage consists of a driver arm, connecting rod, and a follower? ✔✔double rocker
The follower of the ______ linkage moves in an arc. ✔✔crank rocker
A ______ linkage changes rotary motion into reciprocating (back and forth) motion. ✔✔slider
crank
The crank rocker linkage is one type of ______ linkage. ✔✔four bar
A ____ is mounted on a shaft by means of a key. ✔✔cam
The four properties of a cam are: rise, fall, ______, and constant velocity. ✔✔dwell
A cam is a wheel that, when combined with a cam follower, produces a(n) ______ motion.
✔✔reciprocating
Turnbuckle has two bolts, where ______. ✔✔one has left-hand threads and the other has righthand threads
On a CNC milling machine a movement along the X direction would move the ______. ✔✔table
In a CNC machine operation, zero offset ______. ✔✔allows the operator to move the part to the
most desirable location on the work table
During the cutting action, the tool tip ______ the metal until it exceeds its fracture point.
✔✔deforms
Feed of a single point cutting tool most affects the ______. ✔✔tool's life
A built-up edge condition of a cutting tool causes it to ______. ✔✔cut more deeply
Round stock is specified using ______. ✔✔diameter and length
What is used most often to cut raw stock into shorter lengths? ✔✔horizontal band saw
When using a horizontal band sat to cut stock to a specific length, the saw blade should touch
______. ✔✔just the outside of the line you created on the material
On a vertical band saw, the blade guide should be set ______. ✔✔3/8 inches to 1/2 inches above
the stock at its thickest point
A ______ punch is used to create a very small indentation. ✔✔prick
Layout work is the operation of ______. ✔✔transferring data from a technical drawing to the
part
A drill press will under-size the holes if the ______. ✔✔drill bit has a worn margin
The size of a drill is usually stamped on its ______. ✔✔shank
______ are used to life the work piece off the bottom of the vice. ✔✔Parallels
During the drilling of a hole, the drill is raised to ______. ✔✔clear the chips from the hole
Weight can be described as the ______ with which an object is attracted to the earth. ✔✔force
Define discrete manufacturing. ✔✔Products sold by the number (10,000 screws, one million
pennies)
Define process manufacturing. ✔✔Often sold by weight or volume, involves changing the nature
of ingredients.
Define a thermoplastic. ✔✔Plastic that can be reheated and remolded again.
Define a thermoset. ✔✔Plastic that decomposes if reheated.
Define elastomer. ✔✔A material that can be stretched at room temp to at least 2x original length
and it returns to normal.
The coefficient of friction describes the ______. ✔✔friction between two objects
With CNC Milling tool dimensions; the X direction moves the ______. ✔✔table side to side
With CNC Milling tool dimensions; the Y direction moves the ______. ✔✔table up and down
With CNC Milling tool dimensions; the Z direction moves the ______. ✔✔tool up and down
Filing can be used to ______. ✔✔debut, square or chamfer
Round stock is specified by using ______. ✔✔diameter and length
Net-shape manufacturing forms a part with ______. ✔✔only one process
Reamers have ______ cutting edges. ✔✔multiple
A reamer is fed into into a pre-drilled hold ______. ✔✔using one smooth, constant pressure
operation
The drill selected to prepare a hole for a reaming operation should be smaller than the diameter
of the reamer by ______ inch if the finished reamed hole is larger than 1/2-inch diameter. How
about a hole that is smaller than 1/2-inch in diameter? ✔✔1/32", 1/64"
Reamers are used to drill holes ______. ✔✔That have precise diameters, that are smooth on the
inside, only after the hole has been prepared by a regular twist drill
The ______ is used to control how deep a countersink enters the work piece. ✔✔depth gauge
Describe countersinking. ✔✔It creates a cone shaped opening in a hole, it allows a flat head
screw to sit completely below the surface of a part, it also creates a chamfer on a part
The _____ of the counterbore is used to guide the counterbore so that the counterbore is perfectly
aligned with the clearance hole. ✔✔pilot
A counterbore ______. ✔✔enlarges a hole for a portion of its depth
A counterbore has a ______. ✔✔pilot
It is possible to tap a hole using a ______. ✔✔drill press
A tap looks like a ______. ✔✔screw
During the tapping operation, the tap should be rotated counter clockwise for 1/2 turn following
each 1 turn clockwise to ______. ✔✔break off the chips to avoid jamming the tap
The maximum strength is reached when the thread engagement reaches ______. ✔✔60 percent
Proper ______ require(s) that when parts are requisitioned that they are easy to locate and can be
delivered to another department on time. ✔✔material handling
The ______ on a boiler burner makes is easy to detect a main flame. ✔✔UV fire eye
A thorough check for a history of similar problems should occur ______. ✔✔on problems that
keep recurring at regular intervals
An announcement system called ______ (Japanese for signboard) is used to announce the need
for reactive maintenance. ✔✔andon
Companies use ______ to show data about the progress of production. ✔✔job status reports
Manufacturing paths are indicated by ______ documents. ✔✔process flow
A process's ______ is the rate at which a production system creates a finished product.
✔✔capacity
Reallocation of resources is the best way to ______. ✔✔increase production if current
production cannot meet the demand
Red tags are used to indicate scrapped parts while a yellow tag indicates a part that _____.
✔✔has been placed on hold
On a bill of materials, the ______ indicates which parts form each subassembly. ✔✔part level
number
A ______ is a list of all the materials and components required to make the product and the
quantity of each. ✔✔bill of materials
Spare parts used in repair work are typically included in the calculation of ______.
✔✔production downtime
For a 365-day year with 30 days of scheduled downtime, what is the availability? ✔✔335 days
minus unscheduled downtime
As part of a(n) ______, manufacturing see end of line inspections as one form of waste. ✔✔lean
manufacturing process
An increase in the number of inspections is not likely to ______. ✔✔reduce the number of parts
that are out of spec
Companies strive to eliminate waste and non value added work through a process of ______.
✔✔continuous improvement
The critical nature of a job has the least impact on ______. ✔✔job scheduling
An important requirement in order to achieve just-in-time manufacturing is to ______.
✔✔schedule jobs well
When a production line is operating at maximum speed, a need to increase production can only
be achieved by ______. ✔✔scheduling overtime
The elapsed time between receiving a customer order and the product being delivered is called
______. ✔✔order cycle time
Materials ______ forms are important because they allow the company to track of where money
is being spent, and to help in budgeting for operating expenses. ✔✔requisition
______ saves a company money because it reduces the cost associated with maintaining a large
inventory of items. ✔✔JIT
______ includes any materials that have been issued to a manufacturing order that have not been
produced into a finished product. ✔✔Work-in-progress inventory
Kanban is considered a(n) ______. ✔✔pull inventory system
Opportunities for improvement of a process can be tracked by ______. ✔✔a Pareto diagram
(80/20 rule)
Measuring and tracking production is one way to apply ______. ✔✔statistical process control
Companies use ______ to determine how manufacturing methods are most likely to fail.
✔✔Process Failure Mode and Effect Analysis (PFMEA)
A frequency chart is typcally used to establish ______. ✔✔sampling plans
New product design teams should perform a(n) _____ as early in the design process as possible.
✔✔Design Failure Mode and Effect Analysis (DFMEA)
As part of a continuous improvement, companies use ______ to set goals to strive towards.
✔✔product benchmarks
Less-than-truckload (LTL) shipping operates by ______. ✔✔having one truck make several
stops before achieving full load
The ______ is used to identify the items being loaded for shipment as well as the potential
hazards associated with those items. ✔✔A shipping manifest
Manufacturers can save time and money if ______ is used. ✔✔direct packaging
Creating backorders allows a company to save money by ______. ✔✔waiting util a large order
comes in, allowing the setup cost to be shared across a large number of items
A counterbore should be ______ larger than the head of the socket to be used. ✔✔1/64"
____ is a planning tool that expands MRP to include other departments in planning production.
✔✔MRPII
[Show More]