CENSECFOR Operator Training - M9 Service Pistol

Document Content and Description Below

CENSECFOR Operator Training - M9 Service Pistol proper weapon handling is whose responsibility - >>>>The person in control of the weapon pointing of aiming a functional weapon at any person or thin ... g is unlawful except when - >>>>when required in the performance of duty the most prevalent factor in accidents involving firearms is which of the following - >>>>assuming the guns not loaded a weapon's readiness to fire and its corresponding safety status are described using one of how many numbered weapon condition codes - >>>>4 to prevent unintentional injury to personnel or damages to property that could occur when handling or transferring possession of a weapon is the rationale for which of the below safety rules - >>>>rule 1 which safety notation which if not strictly observed, WILL result in serious injury to, or death of personnel - >>>>danger when given the command to LOAD & MAKE READY you should do which of the following? - >>>>weapon condition 4 to 1 to minimize risk of firing any weapon negligently and reinforce positive identification is the rationale for which of the below safety rules - >>>>rule 3 which safety notation if not strictly observed, could result in injury to, or death of personnel? - >>>>warning which best represents weapons condition code 4? - >>>>magazine removed, chamber empty, slide forward, safety on what is the maximum ammo the M9 can hold? - >>>>15+1 What is the maximum effective range for the m9 - >>>>50Meters what is the maximum range in meters of the m9 service pistol? - >>>>1800m the m9 service pistol has how many major component groups? - >>>>3 which of the below sub-component of the M9 service pistol locks the slide rearward? - >>>>slide stop which of the major component group houses the firing pin and extractor? - >>>>slide & barrel which of the sub-component group returns the slide forward? - >>>>Recoil spring the cycle of operation for the M9 service pistol contains how many separate steps. - >>>>8 what is incomplete locking - >>>>slide does not fully lock into battery due to weapon/ammo/magazine malfunction the m9 uses the ___ principle of operation to thrust the barrel group rearward. - >>>>blowback how many safety devices/features does the M9 service pistol have ? - >>>>4 which of the following safety features interrupts the forward movement of the hammer during a mechanical failure. - >>>>half cock safety notch which feature is located internally and considered and additionally safety features that prevents the M9 service pistol from firing fully automatic? - >>>>disconnector the M9 service pistol failing to eject the cartridge is called which type of stoppage - >>>>stovepipe when clearing a stoppage during a navy handgun qualification course, the first action the shooter must do is which of the following? - >>>>REMOVE finger from trigger and place it along side the receiver when clearing a stoppage during a navy handgun qualification course, the shooter must do which of the following AFTER removing finger from trigger - >>>>engage decocking/ safety lever remedial actions for clearing a stoppage during a tactical situation include determining cause of stoppage, clearing the stoppage and - >>>>returning the weapon to operation on the command LOAD, personnel shall perform which of the following steps FIRST - >>>>ensure pistol is in condition 4 what is the first step in receiving a weapon? - >>>>ensure the pistol is on safe what are 2 types of approved M9 service pistol transport methods? - >>>>Holster/Administrative which weapon carry is used when contact with the enemy is imminent? - >>>>ready (22) what is the order of the drawing technique? - >>>>-Grab -Draw -Smack -Look & Squeeze what is the proper reload procedure to use in a tactical situation? - >>>>fast slow fast during which sequence of the grab - draw- smack - look & squeeze drawing techniques do you thrust the weapon forward towards the threat? - >>>>smack weapon should be drawn from the holster ______and returned ______ - >>>>quick /slow squeeze trigger - >>>>soft brush & CLPwrong wire brush & CLP wrong to remove loosen carbon deposits - >>>>wipe and clean patched soaked with CLP which of the following safety features interrupts the forward movement of the hammer during a mechanical failure? - >>>>Half-cock safety notch What should be used in the removal of excess dirt and carbon buildup on the slide assembly? - >>>>Soft brush & CLP which of the following items should be used to clean the recoil spring and recoil spring guide? - >>>>CLP& SOFT BRUSH/ CLOTH what do you use for hard to clean areas on the M9 service pistol? - >>>>soft brush to remove loose carbon deposits from the bore you should do which of the following? - >>>>Wipe them with clean patch soaked with CLP [Show More]

Last updated: 3 years ago

Preview 1 out of 4 pages